Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi
I am giving a try to ESB as an alternative to BLE. I am starting with esb_prx and esb_ptx sample.
That sample works on DK boards.
In order to save energy I would...
Hello to all,
I am using nRF52832 DK with sd132, v6.0.0 and sdk 15.0.0, segger embedded studio. We want to achieve change application timer time (APP_TIMER_TICKS(update_time...
I use nRF52810 and S112 as the soft device. And I use SDK 15.2.0. My BLE device works as a peripheral. And I have to connect some iOS and Android devices with bonding. Communications...
Hello,
I have a problem, I want to measure the power consumption of the nRF9160 with the nRF9160 DK, and I have the N6705B power analyzer, and I like to know how the connection...
Hello dear Nordic community,
We have developed a custom board that contains the nordic nrf52832, which is communicating via I2C bus with a 9-axis sensor (Bosch BMX055...
I am using Softdevice 140 with SDK v15.2 on Segger studio to develope a ble application. when Debugging, the program gets stuck as shown in the attached video. However, the...
Hi, everyone,
We are developing BlueTooth projects on NRF52832 and NRF51822 modules. The projects are built from DFU Bootloader, Soft Device and Main Application. Each one...
Hi Sir,
For EN 300 328 V2.1.1, I reference below setting.
https://devzone.nordicsemi.com/f/nordic-q-a/21643/en-300-328-v2-1-1-receiver-blocking-test-setup/84959#84959...
Hi
I am using TIMER3 and TIMER4 for generating PWM signals using PPI and synchronizing ADC sampling, respectively. I posted the preliminary project in here . After taking...
I am using mbn52832 BLE+MCU module and i am facing issue in one of the GPIO pins.
I am facing issue in P0_29 pin and i am driving the P-channel MOSFET from this pin. I have...
Hi,
I would like to configure the watchdog timer for the nRF9160. I have attempted to run the Zephyr example application (path/to/zephyr/test/driver/watchdog/wdt_basic_api...
Hi:
i am working with Thingy52，and i have get a zip pack named thingysdkv210,today after the compile prcess after following ../PCA20020/thingysdkv210/documentation/firmware_compile...
My problem:
I have to setup a BLE connection between two nRF52 devices one central device and one peripheral device. I have multiple central devices (C1, C2 to Cn) and multiple...
We are developing BLE 5.0 products using the nRF52832 running the Nordic S132 v6.0.0 softdevice and SDK version 15.0.0.
We noticed that one of our test devices, a Huawei...
