Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
nRF54L replaces the RTCs from nRF52 with the GRTC. GRTC only have a single CC which is able to generate repeating events with the use of the CC0 interval register. I would...
Hi,
While completing the nRF54L Series Express course, I noted that USB support is not provided by the bare-metal SDK.
I wanted to check if adding support for this is...
I tried to build the Blinky sample description in nrf sdk fundamental academy training without success.
Error occur during build at B0n stage:
error: 'struct shell_ctx...
## Summary Setting `CONFIG_MEMFAULT_NCS_INTERNAL_FLASH_BACKED_COREDUMP=y` on an nRF54L15 target fails to compile. The Kconfig is exposed (it only `depends on PARTITION_MANAGER_ENABLED...
Hello, one of our devices moved from using the nRF52832 to using the nRF54L15 .
I created new board files and got the old software to run, after some adjustments. The application...
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
I get this error when i try to use FATFS or LittleFS - RAM works though /Users/admin/mass_1/src/main.c: In function 'setup_flash': /opt/nordic/ncs/v2.9.0/nrf/include/flash_map_pm...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
