I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi everybody!
My goal now is to use nRF52832 as a intermediary for an update package. In other words, my goal is to send a file (probably .zip package) to a board and save...
Hi,
When running the unit tests for Mesh SDK 3.1.0 I get the following failures.
83/92 Test #83: generic_dtt_client ...............***Failed 0.00 sec
From the log I...
Dear DevZone,
I'm new to the nRF52-DK and Nordic in general. I'm trying to set up an nRF52-DK to use with nRF Sniffer, and not having any success.
I have tried following...
Hello!
I want to ask about read operation on nrf51822.
In your examples, as I understand, BT stack handles Read Request automatically and then sends Read Response. The value...
Hello,
I am beginner for bluetooth technology and have very interesting to this technology
I have developed new board (4 pcs) for nrf 52832 and soldered all parts from...
Hello.
Please teach me how to turn on DEBUG flag on Segger Embeddid Studio.
Environment: SDK 15.2.0 and SEGGER Embedded Studio Release 4.10a Build 2018110203.37618 Linux...
Hi I'm facing problem while programming my custom nrf52832 board (It might be issue with flash/ROM setting) its saying this hex file has a data in softdevice region . I'm...
Is nrF52840 VDDH pin only used for REG0 LDO/DCDC regulator output to generate VDD power for the GPIO circuitry?
or is VDDH power used to power some other internal circuits...
Is there a way to access the Gazell heartbeat timer? Ideally I would have a callback to my application when the heartbeat occurs. The main motivation for this would be to...
Hi,
What I did:
Already connected the custom board with nrf52832 chip on pc with python
Already receiving data from the board
I want to have the python code that...
The GPS antenna just fell off the board. Seems like the part has a cold solder joint. This led me thinking that the LTE antenna might also have the same problem. I had no...
I choose one NRF52 DK(nrf52840_pca10056) for my daily development. After hundreds of erase and write cycles, the DK won't behaves like it should do. The other DKs runs well...
Hi,
In the registery definition of nRF52840 it is stated for PSEL.TXD:
Reg ID: A -> from bit 0 til 4 for Pin selection
Reg ID: B -> bit 5 for Port number
In this case...
