Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Can anybody help me to get out of this error, Error programming through Seggar Embedded Studio,
Additional Load File[0] "E:/nRF5_SDK_15.2.0_9412b96/nRF5_SDK_15.2.0_9412b96...
Hello.
I try to make audio noise meter on nRF52832. I used analog MEMS MIC with OPA which I turn on via MOSFET while before measurement. I'm using SAADC triggering by RTC...
Hi there,
What changes should I have to do to the light switch example to provisioning the client and server using group address instead of unicast address?
I believe...
In our application we need to have the NFC pins configured for GPIO and APPROTECT enabled.
As an additional safety feature I verify the UICR content inside my application...
Or any general how-to documents when the users want to set up any peripheral using the direct register access? I try not to use SDK for simplify and minimize the code side...
Hello,
I'm trying to implement the Gazell protocol for one of my tasks. I understand there is CRC for the data sent from the device to the host. I cannot however find anywhere...
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
Hello,
Is there any development board like an Arduino mini for the nrF52840. It need to fit a in very small enclosure
Ideally, I would like to test/develop some sensors...
Hi,
I am working with hid keyboard example on my Windows machine.
Problem 1 : After flashing the code, I make bluetooth connection and the code works properly. Then I...
Hi,
I am reading the Product Specification v1.3 of the nRF52832 SoC.
On page 23 the RAM0 block section 1 address is given as 0x21001000.
From the context I believe, this...
As per one of my discussions with , on another thread here , I can send a GenericOnOffGet from my android activity and I will get the status of the light in GenericOnOffStatus...
Again!!! I have a lot of problems to navigate on the Nordic products.
I follow the links and went to the start52840dongle and downloaded the SDK.
I find only stuff regarding...
