We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
Hello,
I'm using NRFX PWM directly because I need something more custom than zephyr's PWM driver provides. I'm trying to understand what .pin_polarity field in the config...
Hello,
When I follow the steps to create a new standalone workspace application for SDK and Toolchain 2.9.0, and then add a new build configuration and build the project...
Hi,
I'm developing a system which needs to have near real time control (downlinks) and uplinks. I've into these 2 issues. Please note that I'm still a beginner with LTE...
Hi I tried to put descriptor on the characteristic recently and it didn't seem to work. Is there something wrong with that?
If I take the following code that adds...
Hi, I have a brand new nrf5340dk and the debug interface is not showing up when connected: I have other nrf5340s that work so I'm sure its the board specific.
Board label...
Hello,
Customer would like to know if part below:
NRF52840-DONGLE
Customer would like to know if there is any connector that Customer is able to use to the above part...
Hello,
I am relatively new to the nrf9161, but I am running into an error with my build.
'TFM_PERIPHERAL_DPPI_CHANNEL_MASK_SECURE' undeclared (first use in this function...
Hi there,
I intend to use pynrfjprog in development replacing another, older library. However, any call to the API which involves the nrfjprog DLL returns:
This is on...
Hi:
MCU: nRF52832
The device is powered by a battery. When the battery voltage drops to around 1.3V but is not completely depleted, if the device is charged at this time...
I am in the development phase of a Bluetooth based system design, which will be able to receive audio stream from any mobile device and play on the speaker, and also it would...
Hi,
I'd like to provision my Thingy91x for use with my nRF Cloud (so I can use location services). How do I provision the Thingy91x for use with my own nRF Cloud? What should...
Hi.
I read on the download site of the nrf command line tools that they are being deprecated.
I want to be sure that i'm correct here: 1. nrfjprog is replaced by nrfutil...
I have an application that runs on nrf9160 and uses nrf52811 for Bluetooth with client-host setup. Problem is it sometimes crashes on startup going into endless reboot loop...
