Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi, I was trying to flash the sweyntooth firmware to nRF52840 dongle using nRF connect for desktop. I was following the instruction on in this tutorial: . The hex file I used...
I'm currently developing a BLE Long Range application based on Zephyr and the v2.8.0 version of the nRF Connect SDK. The app is based on the following nRF samples: central_hr_coded...
Hello,
I am currently stuck trying to migrate a project to the 2.8.0 version of the NC SDK.
I followed the exercice of the Nordic Academy : FOTA over BLE .
It works...
I want to automatically reconnect to my peripheral (nrf5340 DK) from my central (phone) when there is an accidental disconnect (out of range) which I am simulating by resetting...
We are using the nrf9160 with SLM V2.4.2 and Modem V1.3.6 and we can do 6 calls to the Verizon cell network in 3 minutes and 30 seconds apart with no issues.
However, on...
I am developing a BLE application on the nRF52 platform using FreeRTOS. My application involves custom BLE services and characteristics, and I am encountering a hard fault...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
I have a device with 3 major components:
Fanstel nrf52840
PMIC1300
spi display (Waveshare 2.13inch E-Ink Display)
PMIC:
BUCK1: power Fanstel
BUCK2: power...
I am running a modified GNSS demo code for our board. At initialization, there is some traffic going between the MCU and the GNSS chip, but when the demo code calls nrf_modem_at_printf...
I am having a problem after installing 2.9 where I am getting a problem on some projects where the nRF addin does not seem to work
When try to create a new application...
Hi, On Ubuntu, after a distribution upgrade from 22 to 24, NRFConnect has failed in a couple of ways. 1. Upon starting, the application fails with: [7982:0910/180010.628514...
I am facing error while building the sample "Hello World for multiple board targets using Sysbuild" without changing anything in the sample. I am using nRF connect SDK and...
I am using the nrf52840 USB dongle, I flashed it with the OpenThread CLI and I managed to locate my PAN ID, Master Key and Channel from the separate thread/matter dongle for...
Hi,
My custom boards with nRF9151 don't get gps fix. I'm using the same GPS antenna and LNA as DK. Soft is from DevAcademi example, but tried also GGSN sample and some other...
