Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi. I tried using the TWI master and slave drivers on 2 different nRF52840DK boards. The 100KHz frequency is perhaps a little high and I will see how to lower it by acting...
HI ALL,
I want to create a static library in the application layer, but this library will contain nrf related header files, which will cause cmake to not compile properly...
We have a custom board based on the nRF52805 and we're seeing some odd behaviors in debugging / testing that we're trying to nail down. Two questions:
The INFO.VARIANT...
When I use the J-link programming program, the following happens to the J-flash connection chip
SEGGER J-Link Commander V7.67d (Compiled Jul 5 2022 16:15:35) DLL version...
Hello, my custom board is using pin 09 to communicate through uart. I want to check that uart is working on this custom board. First, I tried to create a simple uart application...
I am using NCS v2.8.0.
After successfully running the headset example with one gateway, one left channel receiver and one right channel receiver am trying to get the Auracast...
I spent quite some time trying to understand why I was getting random network disconnect after a totally fine CEREG notification, like in this log:
It turns out that inside...
Dear Nordic:
Light bulb project support 52840DK, can light bulb project support 52840 dongle? I have not found dongle option in l ight bulb boards folder, only find nrf52840dk_nrf52840...
Hello. consisting of nrf7002 + nrf5340, I'm going to do battery management and power management of a circuit that operates up to a small coin electric motor at npm1100, and...
Hi,
I am encountering an issue with the BLE connection on my nRF5340 DK. When I attempt to connect the device to my PC, the pairing process takes a significant amount of...
Hi,
I am implementing a BLE central that is based on ble_app_uart example using nRF52833 with a soft device version 7.2.0.
I have noticed that a single packet download...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I am trying to enable the watchdog in my application, and I can successfully locate the device node and add a timeout, but...
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
