Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello
I would like to sign an image temporarily with west CMake options as described in Enabling a bootloader chain using sysbuild using the comand line:
In it's final...
Dear DevZone:
I use NCS 2.8.0 to build Light Switch FW, my build command as below:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp...
Dear Devzone,
I currently use the nrfutil dfu serial command to upgrade the firmware, which is OK. I want to upgrade the firmware of 52832 through MCU, so I need to know...
Hello support,
We are developing a battery-operated sensor. For that, we are using nrf5340. Also, we made an enclosure for the sensor.
While developing we found that the...
Hi there,
Is switching between UART and I2C runtime on the nRF52840 with Zephyr possible when utilizing the same two pins for TX/RX vs SDA/SCL?
Thanks in advance,
L...
What version of LVGL is used with nRFConnect for VSC 2.7? Where can I find this information generally. It seems like the lvgl version is 8.3, but I don't know why I think...
Hello,
I am writing this thread to ask what would be the hardware configuration for the QKAA version of the nRF5340 chip if I don't want to use the wireless features of...
I am considering using the nRF7002 for a Wi-Fi application. I want to use an nRF54L15 as the host for an nRF7002 and operate it using Target Wake Time (TWT) to periodically...
I need to connect to other units according to their MAC address. I'm assuming that this:
BT_SCAN_FILTER_TYPE_ADDR
Is the thing to use in this:
bt_scan_filter_add...
Hi, I am working on a project where I need to add ble dfu as well as serial dfu issue I am getting on adding serial dfu to ble example I am getting error variables undeclared...
Hi,
My ultimate goal is to add NDT [1] to a meshtastic [2] device implemented with RAK4631[3]. For this goal I can see the following obstacles:
- The meshtastic stack...
Hi,
I am trying to modify the ble_app_blinky example in such a way that I can connect with multiple central devices to on peripheral device.
So far I found a good start...
From "nrf_section.h" (__GNUC__):
Example for the section name " log_const_data ":
NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
I have a sample app (hellow world from the zephyr samples).
It compiled well on my system in vscode using 2.7.0 and sysbuild.
I then installed 2.8.0 and suddenly the build...
