Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Currently, I'm using nRF5340 Audio on a homemade board, and I've managed to get the sound input from the gateway as a LINE input and the sound coming out of the headset, but...
Hello ,
I am trying to program external custom board through another nrf52dk via SWD interface to check if external programming method works. The connections between two...
We are using BLE and QSPI at the same time and want to have maximum RF range. Sensor data is collected, encoded, and written into flash via QSPI. This goes on for a few minutes...
I have a question: Is it possible to use BLE Long Range mode (Coded PHY) in the NRF52840 with mobile phones? If not, is there a solution to use it in parallel with normal...
I am using NRF52840's NFC with apple wallet but it requires certification from Apple to be used as tag reader. How can I get it certified so that I can read data from apple...
Hello,
I need to be able to send/receive binary data over this BLE UART Service (bt_nus) on macOS. I'm using the peripheral_uart sample project with no success. It seems...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
I have a BME688 connected to a NRF52840DK and I cannot get a working I2C communication using Zephyr. Below are all sources:
app.overlay
main.c
prj.conf
I was...
Hi.
I am trying to disable the RESET pin (P0.21) on the nRF52810 microcontroller (custom board) and set it up as a normal I/O pin.
I'm using the SDK v2.6.0.
I don't...
Hi, my device is central device( Central UART ) and I couldn't get stable pairing with peripheral device with display which provides passkey code. The scenario: 1. From the...
Following instruction here for setting up NRF52840-Dongle as a radio coprocessor for use with OpenThread Border Router.
The error is at the second step when executing "...
I'm alter the overlay file to adapt my board.
In my board,I try to use pin 9,10 as uart_tx and uart_rx,without cts and rts.
I wirte it in my app.overlay as follow:
...
I am currently working on a project where I need to connect my nRF52833 microcontroller to other devices using the Nordic UART Service (NUS). I am using the nRF SDK and Segger...
