Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Hello Everyone,
Is it possible to achieve BLE data transmission consistency like there are central and server? The server (nrf52832) reads the GPIO state change and sends...
I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
Hello,
I am designing a battery monitoring circuit for a 3.0V CR2032 coin cell using the nRF52840, and had some questions. I am following the battery monitoring circuit...
PINs 46 and 47 of NRF52832 are Regulator Output according to the specifications. The output reference voltage is 1.3V. Is there any tolerance limit? We currently changed the...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
I have been evaluating the nRF54H20 board and have v0.8.2 of the development kit. Till now I have been using nRF Connect SDK v2.7.99-cs1 branch, I would like to move to the...
I just received a nRF54L15 DK board from Digi-Key (PCA10156 0.9.1) and I'm trying to use the Quick Start app in nRF Connect for Desktop v5.1.0.
After successfully completing...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
Hi,
I'm trying to play some sounds on a piezo with the help of the pwm. I tried to set the period with pwm_set_dt but only the first call is successful and every subsequent...
Hi,
We were building and flashing using v2.7.99-cs1 and upreved to use v2.8.0
When we flashed the boards that had previously flashed and run fine, they now produce the...
Hello,
I am trying to use TIMER3 where it should count 1ms ticks for 15 seconds and then stop.
Tried the below code. However it never enters ISR.
Please let me know...
Hello,
I'm using my nRF52840 devkit together with nRF Connect for Desktop Bluetooth Low Energy (v4.0.4) app for some testing. The app failed to recognize my devkit. It used...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Hi,
I am refering chapter 3 of "nRF connect SDK Fundamental" . ( Configuration files - Nordic Developer Academy )
I am refering few samples like "blinky_pwm", "peripheral_lbs...
We developed a Matter product that uses external flash memory both for firmware updates as for storing application specific data. In the ncs-2.8.0 sdk release the flash is...
