Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
I've been searching threads on this topic on DevZone and I found a couple that concluded that MCUBoot can work with external SPI flashes, but not with an SD card.
Is that...
I am using PHYTEC link board eth ( https://docs.zephyrproject.org/latest/boards/shields/link_board_eth/doc/index.html ) as ethernet shield using SPI on nRF9161.
I updated...
Hello, per the PPK2 user guide, I see that the switching during auto-ranging can cause measured current to be higher than the actual current due to inductance.
To be clear...
Our products use NRF52832 chips in production, and now the finished product needs to do an SRRC certification, but I need to confirm whether the original factory of this chip...
Hey, I need to set characteristic length for a PTS test to MTU-1 Otherwise the test case GATT/SR/GAC/BV-01-C will failed with the message - Failed: Cannot find characteristic...
hello:
My project is based on "esb_rx",NCS2.5.1,nRF52832.I need a Unique address for my product ,so I add flash read/write function for my projict, base on "soc_flash_nrf...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
we are facing an issue of loading the application written with nRF Connect SDK to the nRF52840 which has nRF5 SDK's secure bootloader. Update process should be performed...
I try to enable APPROTECT by nrfjprog but seems not work, I still can read the memory after device (PCA10090) reset.
Here is the commands I test to enable APPROTECT
...
I was trying to update the PPK II software, but I am receiving a error message: "Error: EPERM: operation not permitted, mkdir 'D:\'"
Well, in my Windows environment, the...
Hi,
We have been using the DeviKit for our initial development and now we have developed our own custom board using the nRF5340. I trying to flash the device, but couldn...
Hi, We noticed that if you do not "Disconnect" a SEGGER RTT connection (on the RTT Viewer), the nRF52832 chip latches into using a relatively large amount of power (~3mA)...
I'm running the latest nRF Connect under VS Code on Windows 11.
What used to compile and not show errors (a couple weeks ago, and running 2.6.0) is now showing errors on...
I am having a problem where the UART is getting noise and bad data (I assume framing errors too) with Zephyr drivers. I was wondering how in Zephyr do you check for framing...
Hello,
This demo gives me automatic pairing and password input.
https://devzone.nordicsemi.com/f/nordic-q-a/44658/communication-problems-between-ble_peripheral-and-ble_central...