I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Hello,
I want to design a board with nRF52832 or nRF5340 which contains several sensors, QUAD or regular SPI flash memory, and a TFT LCD. This TFT has an SPI connection...
Hi,
I am new to DevZone as well as BLE development itself. I am currently working on a project and trying to undestand the IDE as well as the processes and workflow of the...
Hello Community & Nordic support, Observed behaviour: my project build with nRF Connect SDk v2.1.1 was with errors
expected behaviour: my project build with nRF Connect...
Hi,
If I run my nRF5340 peripheral BLE NUS service with NCS 1.9.2, I get two different behavior at console.
When I connect from my WIndows PC running nRF Connect for Desktop...
I'm not sure if this code I inherited is using k_poll_signal correctly because it seems like I can handle it in a much simpler way with an atomic variable.
The below code...
I want to use the lsm6dsox IMU on my Adafruit feather nrf52840 sense board, and I should use other I2C, other than p012 and p011, to not have a problem with the other IMU...
Dear team,
I am not able to flash the nrf5340 audio application (gateway) to the nrf5340 Audio DK using SWD from nrf5340 DK. I nrf5340 DK outputs 1V8 logic.
I can see...
I am using S132 in the Segger IDE on an nrf52832.
I am using SDK version 17.0.0_9d13099.
When I call sd_ble_gatts_hvx() from within a GPIOE ISR (externally pin triggered...
Hello,
Looking to see if there is a pinout TABLE for this package. I've seen the schematic drawing already but looking for a table format which is more user-friendly when...
I've set "NRF_SDH_BLE_GAP_DATA_LENGTH" value to 27 on peripheral side, and it've changed to 251 after connection. On the central side, the value is fixed as 27. I believe...
Hello,
We're currently developing PCB with nRF5340_CLAA SoC. For specific reasons, main supply voltage was changed from stable 3.3V to 3.5V that comes from DC/DC converter...
I recently followed the instructions laid out in the "nRF Sniffer for Bluetooth LE" User Guide version 4.0.0 and having trouble seeing the nRF Sniffer interface in Wireshark...
Hi,
I am trying to implement bluetooth uart peripheral for nrf52811. I try to learn the code from example and want to check the result on my board.
When I build the...
Hi,
I'm on NCS 1.9.2, and I'm having a unexpected behavior on the consumer thread of a k_fifo. The documentation states that the k_fifo_get routine removes a data item from...
Hi all.
I was planning to build ble example and combining it with I2C, but I found this error
I check several previous posts on this forum before and solution...
