Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am recompiling a system from a nRF52832 to the nRF52840.
This is a BLE peripheral. I started with a working ble peripheral example so that I was able to start...
Hi, I have started with "__nRF5_SDK_17.1.0_ddde560" ble_peripheral>ble-app_uart example code project( ble_app_uart_pca10100_s140 ).
I work with IAR Embedded Workbench IDE...
My client is attempting to use the Dongle with a Windows 8 tablet. The Dongle shows up in DevMgr as both nRF52 USB CDC BLE Demo and as Communications Port (COMx). However...
Hi,
I'm having an issue with flash usage reporting when building app. I'm using MCUBoot, so 2 images are generated.
First of all, my definition of partitions in an overlay...
HI
1. If we choose a 28.8MHz crystal oscillator for the MCLK of I2S, will it affect BT? 2. In our design, the power supply is VBAT, and the VDD_nRF setting is 1.8V. Does...
I would like to use GPIOTE, PPI, and TIMER to do the following.
I'm using three GPIO pins. Each pin will get square-wave like signals of varying frequency. On each pin I...
Hi Nordic:
we want to add timesync function on nrf5340 ble nus.(1central + 16peripherals, 0.1ms precision )
Such as:
https://github.com/nordic-auko/nRF5-ble-timesync...
Hi,
Can I know how to set the UICR as the default address in nRF52840 SOC with SDK 17.02/17.1.0 by using nRFJPROG command line tool / SEGGER Embedded Studio IDE.
nRFJPROG...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I managed to implement a multilink communication...
Hi, i was working on a project and from one day to the next i am no longer able to flash my DevBoard.
When pluging it in it comes up as "E:\" name JLINK as always, but west...
We have a board that is to be certified by a Chinese test lab, so I need to create an image based on the direct_test_mode sample.
In Zephyr v2.0.0 I created a custom board...
Hello,
We are using nRF Connect SDK 2.0 on an nRF52832 and were wondering if it is possible to use BLE and Shockburst simultaneously? If I compile enabling both Shockburst...
Hello,
A couple of days ago I run the examples direction_finding_connectionless_rx and tx on two nRF52833dk successfully, meaning that I could see the CTE info received...
Hello,
I have reconfigured the nrf_dm sample from ncs 2.0.0 to use Zephyr Bluetooth Controller by adding CONFIG_BT_LL_SW_SPLIT=y to proj.conf.
But then it's stuck in this...
