Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I'm planning to work on a device which should have two nRF5340 modules on a small PCB (they will be max 2cm apart from each other). Both modules will broadcast data...
Greetings,
I am using the NRF53 DK along with the Zephyr/Beacon (nRF Connect SDK v1.91) example for an ultra-low power application. I would like to know how I can change...
Hi,
I have nRF5340 DK and nRF52840 DK and Flashed Central_hr_coded in nRF52840, Peripheral_hr_coded in nRF5340 DK. Followed the steps of Testing as showed in below link...
I am following various tutorials on how to run an example DFU
I've tried: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v17.1.0%2Flib_bootloader_modules...
Hello,
I setup a BLE Peripheral that advertises a service with 2 notifications. Each notification has 240 bytes of payload data. When I connect with a client and subscribe...
Hello,
I followed the following guide for creating a modified Blinky example app that boots from the mcuboot. I attempted to flash both the merged.hex and zephyr.elf to...
I am using NRF52832 DK, SDK 17.1.0, S132 Softdevice, Segger 5.42a and rtt viewer v7.62.
I am using blinky code from example.After building and debug the code I disconnect...
I want to send the data packet from the BLE using GATT service and after that BLE mesh is initialize, using the Mesh opcode need to Disable the GATT service of the BLE. For...
Hi.
In a prototype built for a small group of test users (20-25), we want to implement a simple tactile reset button for use in case of an anomaly (as the prototype software...
Hello,
I am using nRF9160 dev kit in Chicago (USA) and in Aldingen (Germany) where I am using same firmware for both DK to get GPS Fixes for location. But surprisingly in...
good try,
i tried adding buttonless dfu service to ble hid_mouse/keyboard sample in nRF52 SDK 17.1 with PCA10040 dev board but it does not show up in the list of devices...
If the privacy feature is disabled, calling bt_conn_le_create will change the state to BT_CONN_CONNECTING_SCAN (since bt_dev.le.rl_size == 0) and then call bt_le_scan_update...
Hello,
I have been working with Adafruit Feather nRF52 Bluefruit LE for my project, I have two of these modules.
Recently, while I uploaded code into it and push the reset...
Dear Forum,
I am using the provided BLE-NUS UART examples (central/peripheral) to create a COM link via bluetooth.
As I failed to generate a setup which directly operates...
