Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
We are using bl-653,
we wanted to enable UART-1, for bl-653 we wrote overlay & configurations mentioned below:
&uart1 { compatible = "nordic,nrf-uarte"; current...
Hi,
we are observing an interesting range of problems on nRF52840 devices we are assembling, where some percentage of them fail with the following error. While ti may be...
Hello, guys.
We are using nRF51822 SoC together with nRF5 v12.3.0 SDK.
According to the nRF51822 memory layout , half of the 256KB flash memory space is taken by the Softdevice...
Hi, I am developing a zigbee device on Nrf connect sdk 1.9.1 which has 9 endpoints, i am not able to create more than 8 endpoints perfectly.
i tried to change ZB_MAX_EP_NUMBER...
hai,
i am using nrf5340dk NCS (pca10095) v1.9.1 ( using visual studio code IDE )
i want to use nrf5340dk GPIO pins for NETWORK CORE use.
referred Nordic and zephyr website...
I added a new event module to asset_tracker application. The default LOG_DBG messages are very well shown in LTE, but that of my module don't appear in LTE. I replaced LOg_DBG...
I need help extending the LWM2M sample to use PSM to optimize the power consumption of LWM2M.
Scenario:
1. Enable PSM on the LWM2M sample.
2. Set the Lifetime of the...
Hi,
I got a product with nrf52832
i use one uart and i need to add another rs232 uart to it.
Since the NRF52832 has one only 1 harware uart i thought about implementing...
I'm developing a BLE device wich includes the USB Mass Storage feature with microSD card throught SPI.
My developmetn environment: - nRF52833 DK - nRF Connect SDK v1.9.1...
I'm working on the sample ncs\v1.9.1\zephyr\samples\subsys\usb\mass to create a device featured by USB Mass Storage with FLASH memory.
Since I found only old threads about...
We observe something that I can’t explain at the moment. Could you help to find the root of the issue, please? See below.
1. When the battery is connected first, and the...
The Mesh SDK timer_now() function is discontinuous once the overflow counter reaches 256 (and all subsequent times where m_ovfw_counter % 256 == 0). Since the local variable...
hi,
I have a private service with characteristics of lock, unlock, and mode, all of which have write attributes, and only use unlock without read attributes. I can already...
Hello nRF people!
I am developing an application on a custom board with nRF52832, that consumes way too much current, more than intended, and I'm looking for the ways to...
