Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
NRF52840, SDK, nrf5-sdk-17.
This could be a misunderstanding of how the dual bank update works, however I am finding that after an OTA, Bank0 contains the new fw image but...
I have an SPI sensor that benefits from having a precise clock source, and has a muxed pin that can have a clock source.
The peripheral states that this pin can handle frequencies...
Hello Nordic team,
I come to you because I face a strange issue during developing a simple feature using PWM.
For a product, I need to make an LED blink smoothly 3 times...
I have a NRF52840 Devkit and also subsequent NRF52840 boards, and I was wondering if there's any WiFi support on them now. I'm aware that it's possible to use any WiFi module...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
I built two...
Hi All,
I'm new to this wireless field. Is there any impact on power consumption based on RSSI level.
As I understand due bad RSSI there will be retries in communication...
I working on Asset_tracker_v2. After going hrough the code, I estimated the work flow to be as:
1. When either Passive or Active state is intialized, the Sample Timer is...
Hi there,
I am running into this error Update CTE params...failed (err -134) while running the direction_finding_connectionless_tx
The output logs are
can I get more...
Hello,
In the product specification for the npm1100 there is an optional battery monitoring circuit schematic on page 39. I'm having trouble understanding why there are...
As described in the topic, I wrote my own bootloader (located at 0x70000). When I restart from the app (located at 0x26000) and enter the bootloader, NRF_ Log doesn't work...
Hi, I am using a BL653, on which I have the following peripherals:
SPI
I2C
UART
ADC
PWM
BLE controller
Upon bootup I want mcuboot to diagnose these 6 peripherals...
Hey Nordic Team
What would be the expected quiescent current for different versions of the Thingy91 in a lp_hci_uart configuration? For instance, I've noticed that v1...
Hello,
I am a university student that is currently working on a project regarding an indoor RTLS proposed using BLE beacon system to track down an object.
After some research...
