Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I installed nRF Connect and inside it I installed Programmer. When opening the programmer I get the following exception:
And system report:
I already tried following...
Hi,
I currently have a working project with BG96, embed TLS and LWM2M.
I'm investigating some problems that occur when the connectivity is interrupted during TLS handshake...
Hi !
In nRF9160, want to implement nrf_mode_lib for modem. Therefore, need to select non-secure(ns) board.But want to set UARTE2 as secure. As UARTE2 provides communication...
Hello!
I am completely new to development with the nRF52DK.
Today I spent the entire day trying to set up the IDE and enviroment to make my first application, but that...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello All,
I am using the BE33 (nRF52833 based) module of the Celium Device. I am able to flash the code by using SWDIO and SWDCLK pins. Also, I have tested the BLE advertisement...
Hi,
I am running into this issue when receiving over uart where the byte received is always one byte behind relative to the byte sent by the sender. The byte received is...
I've never been able to get >= 10.13.0 of the nrf tools working. The previous versions work fine on my x86 mac, but there are a series of problems with the newer tools. First...
Hello,
Is there a way to configure mcuboot to allow updates to the bootloader itself? That feature is supported in Nordic's bootloader, but I haven't been able to find...
Hi All,
We are using NCS v1.7.1 on our custom designed nRF52840 board. We have a touch screen interfaced with I2C to our device. There is one more controller connected on...
I am making a "program that keeps multiple software in Flash ROM and reads arbitrary software according to instructions".
When I open the hex file with a text editor, the...
So i have my nRF5340 DK and have been pretty successful in getting my Mesh working with some Thingy:52 devices, some Adafruit Feather devices and some Sengled Lamps.
Groovy...
I am trying to read from the LIS3MDL sensor using spim on the nrf52840 dongle. I gave the rx buffer with the length of 7bytes. Whenever i tried to read from the sensor, I...
Speaking with various MVNOs, not all carriers support PSM or eDRX when roaming, so I am interested in the time and wattage consumed transitioning from PSM --> to ready to...
Hi,
I want to connect "nRF52840 Dongle" via SPI to an 6-Axis IMU (Adafruit ICM-20649 / InvenSense). The collected data (cycle = appx. 10ms) should be sent out with BLE to...
