Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Context: nrf52840DK, s140, SDK 17.0.2
Hi,
I need to oversample a few ADC pins with burst enabled at roughly the same time periodically: e.g. oversampling 4 separate inputs...
Hello,
I have nrf52832 dev kit and the device. I try to make smaller code size and setup Optimization Level 2 for size.
BLE works, but when connect by NRF connect and...
Hi,
I am currently developing a product which is supplied with battries (chip is nRF52810). Under normal conditions, the product goes into system OFF mode in standby, it...
Hi,
I'm testing a custom board, based on nrf52832_xxab SoC, with a SWD interface. The board was working fine, but suddenly the debugging interface stopped working. Any idea...
I am curious whether there is a correlation in distance between different devices in a BLE connection.
A picture is attached to describe the situation.
A sensor-board...
Hello dear support team, We are in the process of designing an enclosure for our device. The enclosure is going to be molded and we would highly appreciate your support to...
My requirement is to send from Controller Device to NRF Ble Device through UART of 40Bytes at the rate of less than 1ms. Currently I am using ble_app_uart example as a reference...
Hello,
I am working on the ble_app_template example, nrf52840, SDK 17.0.2 and Segger Embedded Studio version 5.34. I have added multiple custom services to my code, however...
Hello,
as part of my project of wearable solderless modules, I've packed the nRF5340 to the same 20x20 mm form-factor - it was described earlier as part of the https://devzone...
Hi,
We have the nRF52811 in QFN48 fitted to a number of products, with the chip showing 'QAAA0 1850AA'. Does this mean that it's an early Revision 1 ? The Errata in the...
Hello,
I'm new in the Nordic sphere and I'm starting in embedded programming. I was confronted with the following problem and I will try to give as many details as possible...
Hi,
got a question about UART and maximum bytes it can receive in one burst or "packet".
Using nRF52382 and SDK16.
Recently I've been developing a new app in which UART...
Hi Nordic Team/public users,
Request your assistance for troubleshooting the NDK-nrf52840 board that was having a detection issue whereby my laptop/PC was unable to detect...
Hello, I hope you are safe and well during these times. I have created a successful prototype using the Adafruit Feather nRF52 Bluefruit and the Arduino IDE. I think I am...
Hi,
I want to update the DFU with application nRF Connect (Bluetooth) for beginning I want to try with nRF Example in example/dfu/bootloader_secure. The file secure_dfu_secure_dfu_ble_s130_pca10028_debug...
