Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi All
I'd like to implement "Fast advertising" with SDK14.10
Q1: I add some code in advertising_data_set() to do fast advertising, is that correct ?
Q2: If want...
Good afternoon. I have the Zephyr gsm_modem sample up and running for my GSM modem and a PPP connection is established to the cellular network. The example does nothing further...
After I write bonding data to flash memory (SoftDevice has been disabled before the write) I get an APP_ERROR:ERROR:FATAL. But I do not know what is causing it. I do an NRF_LOG_DEBUG...
Hi,
We added new commands for code from openthread and generated .hex file by "make -f examples/Makefile-nrf52811 NCP_SPI=1 FULL_LOGS=1 && arm-none-eabi-objcopy -O ihex...
We are planning to develop BLE and Bluetooth Mesh products using nRF52840. I have a couple of questions in use of Zephyr. 1) What is advantage of building BLE or Mesh on Zephyr...
Hi,
I tried to build the ble_app_uart example for nRF52820/s140. In my project I need to use C++ modules.
My usual approach that worked so far:
Take an example project...
Dear Nordic Semiconductor-Team and everyone else, thank you for helping the thousands of people in this forum an answering their questions thoroughly. I have a question/problem...
Hi,
I have to program the application on an nrf52840 chip that is connected to another MCU via the SPI interface. Since I have to send the image from the MCU to program...
Hi, I am building an application on the nrf5340dk using using nrf5340dk_nrf5340_cpuappns as the target board.
When I have CONFIG_NETWORKING=Y enabled in my prj.conf I am...
What causes NRF_LOG to report 'overflow' ? The buffer I provide is certainly large enough.
I have #define NRF_LOG_DEFERRED 1
What happens if I have something like this...
Hi,
When the Bootloader calculates the application CRC it takes around 350ms. I saw that it is possible to switch off the crc calculation or to use hash for validation....
Hi!
We are working on testing JIG after SMTA process and we'd like to use open source solution for in circuit flashing and testing our product. Project is based on NRF52832...
I am using a nRF52832 custom board based on SDK11 and SD 4.0.2 configured as a peripheral with a GATT server. I am seeing a case where the client is an Iphone XR iOS v13.2...
Hello, I'm struggling programming the Blinky app from examples to my NRF52 DK (pca10040) Here is my script: # 1. Generate settings nrfutil settings generate --application...
Hello, I hope you are doing well.
I am using the nRF52832 with the SDK16. After adding some new custom characteristics, I didn't have enough space in the BLE_GATTS_VLOC_STACK...
