Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I Upgraded the software to V3.6.1. The button "Start DFU" is missing from the SFU mode screen. After choosing a Zip file there's nowhere to continue. Had to downgrade the...
Hello,
I'm developing an application using zephyr, openthread, udp, and nfc, targeting the nrf52840 (currently developing on nrf52840dk pca10056).
I initially developed...
Hi,
I would like to get some information about the reset's reason of my nrf9160 like
- The reason is due of an assert type "xxx"
- Where is the stack pointer
- .....
Hello,
I'm developing a BLE device and it consist of nRF52833 and a external UART component.
ble_app_uart example in SDK v17.0.0 is replaced app_uart to libuarte. The...
Hi,
I would like to know if we can enable codded phy while using mutli peripheral in conjunction with mutli central. Also peripheral should be scannable and connectable...
When creating dfu package using nrfutil, an error is displayed.
When I looked for and checked the file where the error occurred, a problem occurred in Python's max...
I am trying to run nrf52840 chip without debugger.
I want to run peripheral_uart example just to show advertising of bluetooth.
And when I use west debug --runner=jlink...
Hi,
I got a nordic thingy:91 and just play a bit with it and the asset_tracker application. Then I flashed the agps code because just want to send GPS coordinates on the...
I am having issues using port pin 1.00 on the 52840 as GPIO. It will just not toggle.
I can successfully use most other pins, even those on the higher port. For example...
Hi
I have 2 identical PCB just out of production - same FW - one is drawing higher current (about 600uA).
The issue is found in mass production and about 1% is having...
I'm using nRF52 DK to send SAADC data to mobile app "nRF Connect" over BLE.
I'm using this code to send the data, but the mobile app "nRF Connect" can only show integer...
Hello Devs.
I am porting my whole project from the SDK16 to NCS 1.4.1 on my original project I use I2c and other drivers which works pretty well, but I am able to make them...
Hi Nordic,
It mentions that "Gain will be lowered by the specified number of gain steps at the start of CTE. Note: First LNAGAIN gain drops, then MIXGAIN, then AAFGAIN"...
I'm trying the example of [ble_app_uart__saadc_timer_driven__scan_mode] from Github. I'm using PCA10040 / s132. I'm sure this demo code works well since many people from online...
Hi,
I want to develop central code to discover vender specific service using pc-ble-driver-py.
The service_discovery function defined in ble_adapter.py can discover the...
