Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi,
I am working on a project where we need to connect to multiple peripherals which also include mobile devices. (up-to 10) on BLE central.
We need to measure the distance...
HI,
I find that the vs code always loading something as below, the Kconfig has some empty.conf, and can't create new Projects.
Then I return it to V2024.9.87, It works...
Hello, guys
We want to evaluate nRF9151 SiP the following way:
To set it to operate in serial mode in which it is ready to receive AT commands (it comes pre-flashed...
Hi,
I've been developing a Matter device based on the nRF5340 SoC, and have been using the DK up until now. We've been developing a custom board in parallel. I've created...
I have nRF Connect SDK v2.6.1 installed on a Mac, the latest toolchain installed via nRF Connect for Desktop, and VSCode with all the nRF extensions. Everything works pretty...
Hello,
I have a custom hardware, with an external 128MB QSPI flash memory connected to a nRF5340. My current task at hand, is to store firmware update images for MCUBoot...
If I am having a custom board created and assembled using a pcb maker (makerpcb, jlcpcb, or pcbway) what do I need to ensure is on the board so I can flash and debug it? I...
We have a issue about nRF9161 on our custom board.
we flash hex our board. It doesn't work very well. sometimess it work and consume about 90mA current. sometimes board...
I have the following setup in my overlay file:
relay { compatible = "gpio-relay"; relay1: relay_1 { gpios = <&gpio0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; label = "DC Mtr...
In our project we use a SHT4x sensor connected to I2C bus of nRF5340. To lower power consumption during idle/sleep we've a power line switch to disconnect the SHT4x from the...
Hi Nordic team,
I was testing whether Zephyr's LLEXT would work on the nRF52840DK. The example can be compiled on NCS 2.7.0 and loads fine. However the final step of having...
I am working w/ the nRF5340DK, and the project mentioned here (NCS v2.5.0, nrf/samples/crypto/rng). I was able to build/flash the project.
I wanted to verify whether the...
Hi,
I am getting to grips with the device tree and when i add an over lay file to the project, the 'new' devices are flagged with the waring that theyre being over ridden...
Hi,
using nrfutil pkg to generate the settings.hex file for the DFU is exceptionally slow on my M2.
I'm using what I believe is the latest version
nrfutil 7.5.0 (063f665...
