Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Is nRF Mesh app support feature that send customize data/command to node? The goal is to transmit data from phone to node, where it will be processed and used to trigger actions...
Hi
This is my first time using nRF connect and Visual studio but I have been following through first the Fundamentals course on the Dev Academy using the nRF52840 DK with...
Hi
I found some Bluetooth send the data unstable problem after i enable the usb cdc acm function. Can you help me to
check my setting that has missing or not thanks. ...
Hi,
I am adapting the Azure IoT example for use with the nRF5340DK and nRF7002EK.
The configuration is:
- sdk: nvs 2.6.0
- example Azure IoT hub
Initially, the getaddrinfo...
Hi Support Team
We test the nRF52840 power consumption of Thread Device follow the below links document.
(+) Analyzing power consumption in Thread Sleepy End Devices...
Hi,
I'm trying to increase the UART buffer size for the asynchronous UART API, but I'm encountering an error. When the message size is set to 255, I can successfully receive...
Hello all,
I config nRF52840 dongle P0.24 and P0.22 as GPIO_OUTPUT. But when I change their value, they are always 0.
I use the same way to change other pins such as P0...
Our product works fine. But I was wondering if we should be completely disabling the NRF_LOG functions for production builds. I suppose it could be using some power and processor...
I'm having a really frustrating time with a custom 7 segment display board I'm developing for scorekeeping. It seems to be successfully flashing using a Segger EDU mini, but...
Hi, I have a nRF52840 DK and I tried powering it with a USB cable. The issue is when I look into device manager the device is not showing up, and when I try connecting the...
Hello !
I'm struggling a bit with the USB HID boot protocol, I have a lot of stack overflow error when trying to do operations while in the get_report callback.
I know...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
