Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello.
The MCU of our new design will be the nRF52832.
I would like to know if it is ok to read the voltage of the battery that powers the system, nominal voltage of 3...
Dear support team,
1. Can mesh provisioner configure multiple devices at one time? For example, there are five unprovisioned devices within the provisioner's network. Can...
Hello,
I cannot flash the nRF52840 Dongle using Programmer 4.3.0 with hex file sniffer_nrf52840dk_nrf52840_4.1.1.hex.
The option for writing is grayed out. =
- python...
While developing, I usually connect to the Serial COM Port to see my print statements.
However, when the devices crashes, only "*** Booting nRF Connect SDK v2.5.1 ***" is...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
We're trying to connect to our Azure Iot Hub using the Azure Iot Hub library provided by Nrf Connect Sdk 2.6.0 (without DPS). We're currently using the evaluation board to...
Hi,
I went through the Nordic Academy nRF Connect SDK Fundamentals - Serial Communication. I tried the exercise program where LED1, LED2 and LED 3 are toggled by pressing...
Hi Support Team,
Have a nice day.
Board : NRF5340DK
Python version : 3
nRF Connect SDK version 2.6.99
We are selecting the NRF5340DK for development purposes and...
I want to send the data from internal sensors via ble from thingy91 . not by usb , and by the way i can't by esim because im from tunisia and the lte-m does not work here...
Hi,
currently I'm facing an issue with the power consumption of my pcb. The idle power consumption is at about 20 µA. After initialising the UART it goes up to over 1 mA...
Hi,
I want to connect X-NUCLEO-NFC08A1 with ST25R3916B to nRF5340 board by adding a SPI node to device-tree source. After compiling and flashing the board, triggering interrupt...
Hi all,
NRF52832 NRF Connect 2.6.0
We need to configure interrupts on a GPIO on both edges. T here are several topics recommending to use GPIO_INT_TRIG_BOTH instead...
I'm getting started with nrf52840DK.
But when i connect my USB i get this error message:
i saw in this topic that when i press on the boot/reset long press when turning...
Hi all,
Could anyone share a code example for sending sensor data over BLE using the NUS Service in Zephyr RTOS? I'm new to this field and struggling to get data from the...
Hi
I use nRF7002-DK, SDK:Ｖ2.5.2 with zephyr driver, I need to send recieved data or command from uart, data type is using with hex byte array to send, from example , the...
