I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hi,
NCS2.0.2, nRF5340 audio DK, VScode
about Le Audio
1.CIS mode,when is bidirectional communication supported?
2.when LC3 support 16bit 16kHZ?
3.when suppourt DFU...
Hi i wonder how could i program the nRF Dongle with the sample thread_cli in order to being able to use the thread topology monitor?
I know that i have to use the Programmer...
I connected my NRF52840 DK board via USB to my Macbook Air. In VS Code, under "Connected Devices" I was expecting it to show up as "NRF52[...]" but it is showing up as "NRF51xxx_xxAA_REV1...
Hi,
follow the to do DFU over UART on nRF5340, it fail in the last step "image confirm".
The console show
What is the meaning "Error: 3"? How to fix it?
Can I...
We have relatively big model composition, and reading it via nRF Mesh app fails if it exceeds 21 segment message.
However the limit I assume should be at 32 segments and...
Hi,
We have done a lot of projects with nrf52832 with softdevice S332 v5 before.
Now we have a new project to use nrf52840. Can we use the original s332 version? Or do...
I and looking at using an nRF52 device with the nRF Connect SDK version 2.x with a Zephyr Bluetooth LE Controller in a peripheral application where the advertisement data...
Hello,
I am running windows 10 and started the DevAcademy lesson 1, exercise 1 and exercise 2.
Up to exercise 2 item 4 (add a build configuration) everything went fine...
Hello i am using an nrf52840 s140 and i am trying to write a specific event when takes place to the usb port. I am using the usbd_uart example.
It works fine for the first...
I used Nrf9160 to develop a product. Until yesterday, I had been able to connect to the nb network normally. But today, I found that my device could no longer register to...
Hi, I'm looking for help installing the nRF Connect for Desktop 3.12.0.
I've managed to unpack the application EXE and have picked out all the required pre-reqs to do the...
Hi,
I have a problem, When I first initialize Bluetooth and then initialize FDS for writing, it will fail. However, if I first initialize FDS and write data ,it is OK, then...
Hi,
We develop a custom gateway in which we use iMx6ULL and NRF52840. Both are connected over full UART.
We use this NRF52840 as a BLE HCI controller by flashing the HCI_UART...
I'm following the Nrf Connect SDK tutorials on YouTube and I am at step 3 ( nRF Connect for VS Code, 3: Building an application & Exploring windows ). When creating the build...
