Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v2.0.0 Hello. In my project, I want to make sure that my project always works during power on. How can I check if my project can...
I am using a nRF52832 with a LISD3H accelerometer. When I initialize the twi driver, I see a ~250 uA increase in current. I was hoping to initialize the twi driver, enable...
Hello,
I use nRF52832 and SDK 17.02.
I use app_button library to detect and handle button pressing.
Everything works fine except that I have a testcase that is to...
We have a very simple application with an out-of-tree driver that is working fine with NCS 2.0.2.
However, changing to NCS 2.1.0 or 2.1.1 results in a DTS error:
(the...
I am working on a project that uses image differentiaton,person/animal detection, etc. To accomplish this, I can either use OpenCV library or use TinyML lite. The problem...
Hi Nordic:
Maybe it isn't a really question. When I try to make an error check, I get two types of error checks, ERROR_CHECK() and APP_ERROR_CHECK(). It seems to be the...
We would like the Fjorden Grip also to trigger the native iOS camera's shutter button, via sending a “volume up” command—similar to selfie sticks, which however use classic...
I was working and testing protobuf using the zephyr example (nanopb) on 1.9.1 SDK. but in build step fails with this error: ModuleNotFoundError: No module named 'google':...
We would like to use an external oscillator instead of External crystal. Is it possible to use external oscillator? If yes to which pin it should the clock be connected ?...
Hello Community,
My customer has design a custom board using NRF52832-QFAB MCU. They have also written application firmware as per product need.
Now, Customer wants...
Greetings,
I recently started working with the NCS and successfully modified the peripheral_uart sample to read data form an I2C sensor and send it via BLE
I wanted...
I was using sdk 1.9.1 into my project and every things waking prefect which use openthread. I took the same project and build it in latest version ( sdk v2.1.1 ). when I flash...
We have created a zigbee custom sleepy end device with the base from light switch example. We are able to perform most of the operations successfully.
We have set the following...
in main.c, you have this code
but if you set CONFIG_BT_NUS_SECURITY_ENABLED=n in the prj.conf file, then there are #defines that will prevent the definition of the...
