Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm attempting to create and then update some NFC data to be presented as a type 2 device.
When I call nfc_t2t_payload_set it returns -45 (EDEADLK) but since the library...
We are using the DFU workflow available with nRF5 SDK 16.0.0 and nRF5 SDK 17.1.0 on our BLE devices. We have two different products, one using the nRF52832 and the other using...
If a manufacturer ships a large number of nRF52840 based devices that are configured as Zigbee end devices, and then later decides to switch them to Zigbee routers through...
I am using the Sparkfun thing plus nrf9160 feather with SDK 2.0.0 and modem firmware 1.3.2. Ultimately I would like to get LTE working along with GNSS, however, I can't even...
Good morning.
I am looking for an example of how to program the u-blox NINA-B221 module using the AT commands so that it is compatible with the application of the Nordic...
I've just updated from nRF Connect v1.9.1 to V2.0.0. In my bluetooth code that worked in the older version, I setup a couple of callbacks for BLE pairing:
In v2.0.0, I...
Hi, We are developing with the nrf9160dk as our development board. We are working from the aws-nrf-cloud a-gps sample (cat tracker sample) for our stack as our main system...
I'm trying to work out why this happens, but am not a great expert at linker scripts. Currently, we use arm-none-eabi to build our projects (and cmake) to great effect. I...
Hello,
we are using the following equipment:
- nrf5340-DK Board
-Zephyr SDK 1.9.0
Our application is intended to transfer a large number of data over BLE.
So, we...
I would like to test nRF52832 passkey method with pc-ble-driver-py ( https://github.com/NordicSemiconductor/pc-ble-driver-py) . Does pc-ble-driver-py supports passkey? Where...
Hi, I am developing an application that includes the following features: 1. PWM to control the buzzer 2. 2 Uarte to communicate with 2 external devices 3. BLE to wireless...
I am trying to speed up the burning process.
I am using JLink ULTRA+ (swd max speed 50Mhz) and Jlink base( swd max speed 30Mhz) and NRF52833 but still get almost the same...
Hello,
We developed a system that consists of 1 central and 10 peripherals, all are based on nRF52840. Below is the configuration of the system:
Central: AWSFreeRTOS...
