Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Battery free BLE solutions are exanpding (wiliot, nexite, atmosic etc). Is there a plan in Nordic to provide a low power chip that will support battery free (or at least ...
Hi, I test the TCP/IP AT command in 9160DK, I download the example Serial LTE modem,
I send the command as below picture.
but it reply as below
==================...
Hello,
Is there any special area where I can save custom MAC address for each device ?
Basically I need to assign unique name and MAC address which the DFU and application...
Hey Forum,
I am using the USB Composite Keyboard example using the standard Descriptor given in the example.
I am able to get all the keys on the Host with a small caveat...
Hi,
I'm trying to use the GNSS application for the nRF9160 to compare GPS antenna performance. There is a Linux utility, GPSMON, that I'm trying to use to display side by...
I use FDS to store some application data. I performing accelerated life testing that randomly power cycles the nRF52840 (on time 4 - 10 seconds) while a central device ( Android...
Hi,
I am trying to run the fat_fs example from zephyr samples on nrf52 development kit (nrf52832) but during building I've got following error :
That's my development...
I am working on UART example and serial port.
I got compile error and modified retarget.c line 99 with
#if defined(__SES_VERSION) && (__SES_VERSION >= 34000) && !defined...
Hi，
I have a circuit board, which is powered by the battery and runs the Bluetooth program. When the power is normally supplied, it runs well. Once the USB charges the battery...
Regarding the capacitive sensor driver with adc for nrf51 series, how am I supposed to wire my board for this to work?
https://infocenter.nordicsemi.com/index.jsp?topic...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
Hi,
I have a central that uses PM to connect to some peripherals.
If I connect to a peer (connection handle 0), and disconnect this device (e.g. by shutting it off). I...
Hi Nordic team,
We have just received our PCB prototypes with nRF52840 chip. While testing BLE functionality we found that the BLE is very weak. The connection is lost within...
Hi,
I'm trying to evaluate nrf5340_audio, but I get a build error as below.
> Executing task: nRF Connect: Build: nrf5340_audio/build (active) <
Building nrf5340_audio...
I'm trying to receive an HTTP response of approximately 100KB using the nrf9160 modem. When the response size is small recv works fine. When response is large recv returns...
