My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi, I want to use TrustedFirmware-M as a secure backend for an application that uses Mbed TLS in the non-secure domain, and this seems to be artificially limited - the MBEDTLS_USE_PSA_CRYPTO...
hiii,
I'm using the light switch example from the mesh SDK, version 5.0. I've successfully configured the client and the server using the nrf mesh app. however, my client...
When I do a 'build and run' in Segger Embedded Studio I get this error
Then I press the reset button and everything works.
If I do 'build and run' again the error repeats...
Hi
I would like to add to the scan_adv example, the possibility of the FOTA upgrade.
I can merge the scan_adv and smp_svr examples, and get them to work at the same time...
Excuse me:
1、The customer wants to use p0.21 pin as General purpose I/O，Can the reset circuit of p0.21 pin be removed？
2、The customer said that when a new nrf52832 chip...
Hi,
I want to add DFU over mesh and usbd into the client example.
I have faced an error of Multiple definitions of UARTE0_UART0_IRQHandler. I comment out the UARTE0_UART0_IRQHandler...
Hello,
i am currently trying to create a project that uses the NRF52840 board as a switch to control sylvania smart+ A19 filament light bulb.
However, i am unable to detect...
Hi,
I'm using NRF52840 in order to implement an application which will connect to a mobile device with PIN code (MITM). In addition - my app will be able to connect to a...
Hi everyone,
I'm using the nRF5340 board, nRF Connect SDK v1.5.0 and the nRF Connect app.
I am also using the example code "beacon" and all the data with integer format...
Hello,
I have been developing a serial C# application to work with the nrf52840 chip, initial development was done using the nrf52840 development kit which worked without...
Good morning,
I am using SDK 16.0.0 and nRF52832 uC. I have a project where I need to connect the uC to a CoAP IP. The only internet access it has is through an SoC developed...
Hi, Usually we set FLASH_START macro to indicate application start address, I do like to consult is't possible to change the FLASH_START from prebuild binary file without...
Excuse me:
PCA10095 cannot be download .hex on SES and nrf conncet programer,The figure below shows the problem downloaded on SES.How to solve tihis problem？
Hi, dear Nordic & all：
When I run libuarte example，I found a problem， I just set P0.14 to high at the begin of mian function, then I send data and test the example's function...
