Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hello NRF Community, I am trying to interface the Adafruit PDM MEMS Microphone (Link: https://www.adafruit.com/product/3492) with my nrf52832dk. However, it fails every time...
In NCS 3.1.x it is now necessary to generate code using the .matter file during the build process. However this is failing on Windows because there is a typo in the chip_codegen...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
I followed the steps below to set up my development environment, based on the instructions from link
Setup 1 1. Installed SEGGER J-Link v8.56a Path: C:\Program Files\SEGGER...
We have this custom sensor board, running nRF9160.
Application code built with SDK 2.5.0, running modem FW 1.3.2, and using LTE-M connecting to MS Azure IoTHub with MQTT...
Hello, I have an application, that uses the Bluetooth to do over the air updates using these two configs:
CONFIG_BOOTLOADER_MCUBOOT =y
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Hi all
I’m having a horrible time trying to get an nRF7002EB Wi-Fi coprocessor working with a nRF52840 via QSPI interface in nRF Connect SDK 3.0.2 (Zephyr 4.0.99). I'm using...
Hello,
We are working with Onomondo in integrating their software SIM. We have it working and sending and receiving data, but am having some issues figuring out what is...
Issue Summary: When running west flash to program my board using the UF2 runner, the process fails with an OSError related to copying the .uf2 file to the UF2 bootloader drive...
Hello!
I can use the offloaded sockets driver with these configuration options on the native_sim target:
CONFIG_NET_DRIVERS=y CONFIG_NET_NATIVE_OFFLOADED_SOCKETS=y
However...
Problem:
I am working on USB, CDC ACM, USB Mass Storage (using SD Card). I currently want to be able to still use the USB stack functions with only my USB Mass Storage being...
I'm experiencing an issue with my Power Profiler Kit II (PPK2) when using nRF Connect for Desktop .
System configuration:
nRF Connect for Desktop version: 5.2.0
...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hello Nordic team,
I would like to check if you provide a template for RED-DA EN18031 for nrf52840 which we can use to modify and fill based on what we have implemented...
I use nRF5340 audio DK,iso_time_sync example, can successfully send BIS data, then I use DK as controller, bumble( google.github.io/.../index.html) as host and it fails to...
