Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Because the GPS will continue to output data after starting, in order not to block the main thread, I placed it in another thread, but I found that when my main thread did...
It is not clear from the website whether Nordic has produced an LE audio chip/board, and if/when it will be available for purchase? Does anyone have any info on it?
Hi,
We are porting our application from nRF Zigbee & Thread SDK to NCS.
On the ZIgbee side, we have been using this methods:
1. zb_zdo_find_bind_src(): to check...
I'm working on a project that has multiple custom partition manager configuration file that are implemented based on the instructions provided in this section of the partition...
Hi,
yesterday, I met the same situation as here . But now, I can't even see one log, even after I annotated the code related twi and just remained some “NRF_LOG_INFO（）”...
Hi,
I am using SDK 17.0.2 for a simple scanner project, where nordic SoC is communicating with main MCU via SPI. The code starts normally on nRF52832, but on nRF52833, it...
Hi,
I am running the example ble_app_att_mtu_throughput with the nRF5 SDK on two nRF52840-DK dev kits. I have flashed both dev kits with S140 soft devices prior to flashing...
We are finalizing a product that has a BL652 (nRF52832) in the main unit and a BL651 (nRF52810) in a remote control unit. We are trying to get our regulatory radio testing...
When I changed HFCLK from "64 MHz internal oscillator (HFINT)" to "64 MHz crystal oscillator (HFXO)", the power consumption when executing sd_app_evt_wait() became larger...
Hi,
We've created a FW image targeting a PCA10056 which consists of our application FW, the example secure DFU bootloader over USB, and the softdevice. Everything works...
I have the ws2812 example working with ncs v1.5 on board actinius_icarus_som
However, when I combine it with other code such as for a custom SPI device and udp comms it...
Hello,
I contact to you because a customer is interested on the RF System, part number nRF5340-QKAA-R, and they asked the following below;
"
Customer wondering if you...
I added FOTA_DOWNLOAD and MCU_BOOT to my project.Then I want to use http to download a file, and an EBADMSG error occurs at this time.
I reproduced this problem in the download_test...
We have an I2S implementation that I based on the example code, but using the nrfx driver. Audio plays fine, but after I call nrfx_i2s_stop, I first see that no next buffers...
