My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi All,
I'm trying to interface a SD Card with nRF52840 DK.
I've got a SD Card socket and a FAT32 formatted 8GB sd card.
When I run, fatfs example , I get following...
hello,
i am using nrf52840 in our customised board with sdk 15.2 and trying to achieve long range with coded phy using long range demo example as base now i could be able...
Hi,
I have two boards NRF52840 DK and I wanted to use example for BLE Central&Peripheral NRF Relay. I have just run example with Heart Rate peripheral and I can see that...
Hi there,
When I program my nrf24le1 in Keil uVision, I notice that when I load the program to the flash memory of the connected motherboard6700 with the nrf24 radio module...
I have downloaded the Kiel and uVision file (the nrf Probe) found here: https://www.nordicsemi.com/Products/Low-power-short-range-wireless/nRF24-series and have gone through...
Hi,
I am using Keil 5 (downloaded with this link: https://www.keil.com/demo/eval/c51.htm ) and have downloaded the nrfProbe to this file. This is being used to program...
Hi, I am try to implement UART SERIAL Bootloader for my device and I just need to perform DFU using uart serial
I have tested the code and bootloader. My query is
Without...
When I run the "ble_app_blinky_pca10040_s132" example from SDK 17.0.2 and 15.2.0, right after Connected I'm seeing that device is Disconnected from device.
I tried with...
We need to programatically (on the Raspberry Pi using Python) send and receive characters to and from a smartphone using a custom service over BTLE. I have used the blinky...
I am trying to communicate with my IOT using wired uart serial port. I am using 840(MCU) (with softdevice #113).
code:
My Issue: Each time I am trying to run it while...
Hi,
I am trying to reduce the consumption of my Thingy91 device in idle mode. I am working with NCSv1.3 and the example asset_tracker. I am currently registering 0.60mA...
In our NRF9160 application, we do not have a UART available and have to implement other means of logging crashes.
We have written our own k_sys_fatal_error_handler but it...
I am using a generic nRF52 dev board with the Arduino nRF52 core . I am trying to get a sample BLE service to display, but it cannot find it on my BLE scanner. After I couldn...
Hi,
I am trying to read read all nearby base stations' Cell ID, TAC, MNC, MCC.
Is this even possible to do with this DK?
At this point I have found these commands...
