We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hi,
I am exploring the idea of removing the JTAG port from the PCB to make it difficult to maliciously change the firmware on the field. I have the secure UART Boot-loader...
Hello
I am developing a firmware for nrf52832 using buttons like if I continuosly press my button for 6 seconds it will go to active mode from sleep mode and have been using...
Dear sir,
I have a light sensor connected to P0.04/AIN2 on 52820. How can i get the change of voltage?
I use the COMP, and has enabled COMP_ENABLED in sdk_config.h, compiled...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
We have a standalone application with no SDK integration. We would like to have the possibility to do OTA Updates via BLE and maybe introduce BLE support later on.
So for...
Hi,
I am trying to run IPSP example from nRF Connect SDK 1.4.2 IPSP sample (v1.4.2\zephyr\samples\bluetooth\ipsp). The "ping6 -I bt0 ff02::1" command is working fine but...
Hi, I am using the nRF52840 DevBoard with SDK 16.0 and Mesh SDK 4.1 and am building on the light_switch_client example.
I am trying to change the publication address by...
Hi,
I'm using nrf52 with s132(v17.0.0).
When I connect nrf52 with my phone, there is error like this picture.
And, the code is
When the buffer is filled, then...
Hello.
When I use NRF_SAADC_INPUT_AIN7 in SAADC, I get an error in calling nrf_drv_saadc_channel_init(). Looking at nrfx_saadc_channel_init() in nrfx_saadc.c, it seems to...
Hi,
In order to determine signal strength we parse the AT+CESQ response and regularly get +CESQ: 99,99,255,255,255,255 (the final number being the strength), but the connection...
Hi,
1、If I want to devlop zigbee with nRF52840, whether the only one sdk series is `nRF5_SDK_for_Thread_and_Zigbee_xxx` ?
2、Can BLE coexists with Zigbee in a nRF52840...
Hi,
I am using a nRF52832 module to receive some data from another nRF52832, which is sending the digitalized data to the receiver. My receiver consists of a nRF52832 module...
Hi guys,
I am trying to add some BLE OTA functions to my NRF52833 running Zigbee. I have looked into the examples in the SDK, and i can see that there is an example for...
