We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
May I know what is the difference of three PNs NRF51822-QFAA-R (H0) AND NRF51822-QFAA-R (G0) AND NRF51822-QFAA-R?
How to identy the three PNs? May I know if NRF51822-QFAA...
I am trying to implement a scenario where the system will be sleeping for a mentioned period of time and then wake up and advertise and transfer data over BLE.
I am using...
Again, if the search engine in your documentation were decent, I would probably not need to ask this question here. The answer probably exists, but try an find it not knowing...
Hello Nordic lovers,
Happy Merry Christmas.
In ble_uart code, I'm interfacing the FreeRTOS & twi_sensor code
The program executed without any error.
And it starts...
Dear Members,
How can I wake up the chip without a button
I'm using the example for Ant,
Ant_bsc_rx .
I have disabled the button with :
bsp_init(BSP_INIT_LEDS...
Hello and Merry Christmas,
Trying to get Thingy:91 connected to cloud. But no such luck.
Followed the video, but somethings are shown. Installed latest firmware (SIP modem...
Hello
I have two questions. Your thoughtful response will be appreciated.
1) What's the impact on power consumption with 1 Mbps vs 500 kbps vs 125 kbps for the same amount...
Is there any way to leave the PPK 2 output enabled when I leave the Power Profiler app? If not, then can I submit this as a feature request?
Without this option I have to...
1、Does Nordic 5340 support 1443a protocol；
2、When the chip（5340） is not powered, does NFC function support passive swiping card
3、Can the reading distance of NFC be more...
Hello
I am using the APII described here:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/include/modem/modem_key_mgmt.html
to add keys to the modem...
Why does the nRF9160 Tx power fall far short of the specification? Its seem to be a false claim that the nRF9160 is a 23 dBm device, and rather is a 20 dBm device. In other...
In the flash write example code the very start of main.c has the following lines
The comment says "Use last page in flash". However, what I am guessing from the code itself...
I am trying to use nrf_serial with IRQ. Tx operations just fine but, i can not get any interrupt when a data comes from uart. I am using sdk 14.2 and not using ble.
Hi,
I am using SDK 14.2 and made some changes with serial example in the SDK. It works just fine while debugging but outside of debugging does not work at all.
I have...
