Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I use a Bluetooth chip nrf52832. I want change the name of the device with the UART port from my Windows PC, but I don't find command or byte to change the device...
I've managed to find some magic numbers/commands for working with nRF5x devices using the CTRL-AP interface, but having no such luck with the commands on an nRF9160. I've...
To the kind attention of Nordic support team,
I didn't find in SDK16 any SES version of secured usb bootloader for PCA10100 (tell me if I'm wrong). I mainly modified PCA10056...
Hi
Accordingly to Datasheet:
Both the nRF51 mbed interface FW and the J-Link OB image can be downloaded from www.nordicsemi.com.
i have the mbed FW on my Dongle and...
Hi,
I need to add custom information into modem and have found that in v1.2 new ODIS fields were introduced.
As I see I can provide any text for device ID, manufacturer...
Hi Team,
I am using latest Mesh SDK and nRF5 SDK.
In sdk coexist example for nRF52832, I tried adding provision over GATT bearer support instead of ADV bearer. After changing...
Hi to all,
I'm slightly going crazy, I'm looking for information related to LE Audio DEV Kit, all the information brings me to KIT rn52 (ok I'll take it now!) But no one...
Hello, I am building a power switch for my application and have some questions about expected behavior when holding a GPIO output signal at HIGH during System ON sleep mode...
Hello, I tried to merged two examples from SDK
1) I run ble_app_bps example from SDK 15.0 HW - PCA10056, nRF52840
2) I included to the main.c
3) I defined in sdk_condif...
Hello,
I am working on a little app running on nrf5340 app core. Now I want also to program the network core, to be able to exchange data via shared memory as little demo...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
