Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Is exist any way to detect IDLE RX line on UART?
I try to use RXTO but this is seted each time when 1 byte comes.
everytime, it changed size of data which will be readed...
Dear Team, I'm preparing an application for nRF52840 that will require to send and receive data collected from two different sources, I2S and UART, two UART or SPI and UART...
Hi Nordic,
Please provide the way to debug not able to write 14 Bytes data into Queued Writes module, my application not get any nrf_ble_qwr_on_ble_evt.
[Project Informaiton...
I am a little bit confused on the steps I need to follow to program the settings and the bootloader files. According to Secure DFU over Serial example instructions ( https...
Hello,
I am trying to download the program to my target using J-LInk. Unfortunately, I get this message (see bellow) and I don't know how to proceed.
Any help is appreciated...
Hi,
I am working on a project that utilizes mesh technology. I'm currently using nrf52832 with NRF Mesh 4.0
There are multiple devices that can act as a server and a...
Hi Folks,
Need some advice. We are sourcing voltage to a variable resistor from an output pin. We've configured this as a high ouput. The overall resistance of the POT...
Hi,
I'm testing ads1292 sensor with nrf52832.
I got some problem when i use spi manager library.
I'm using ble_app_hrs project.
If i use spi manager without advertising...
Hi,
We build a new board based on nRF52833 wlcsp,
I tried to run a simple code with BLE peripheral (ble_app_uart example), and I noticed that the HFCLK is not working...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi
I am running this example from SDK 15.2.0.
I am trying to figure out how the server knows at the end of the session how many bytes of data the Peer received.
Anyone...
The information on the website currently only supports nrf52840.
Can nrf52833 support DFU over USB?
If yes.Which example can be used? Does it use the same DFU USB bootloader...
Hello, I am studying the peripheral/ble_app_uart and peripheral/ble_app/template examples to understand the proper way to build a peripheral with our own set of services and...
Hi,
I have hard time to setup west in my Ubuntu PC. It was installed, but not fully working. So I tried to uninstall and reinstall, and also one time, I may have upgraded...
