Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
I have a device that samples data from a bunch of sensors every n hours, and that when in IDLE must consume around 100uA. To achieve this, I'm using a counter (that...
Hi,
I connected MCUBoot and FOTA to my project. I checked that the download is working, but not stable. I saw in the documentation that you can enable the continuation of...
Hello I need a falling edge response via GPIOTE. The settings I use for sdk 16 to sdk 14.2.0 do not work. For sdk 16 I use the functions nrfx_gpiote _..., for sdk 14.2.0 nrf_drv_gpiote_...
I observed a peak of 334 ua during system-on low-power mode during idle time which is periodic around 4 sec. I am using ble with RC clock option.
1.is it waking for calibration...
Previously, I learned that BLE is capable of 1:1, 1:N, and N:N communication, but I didn't get the exact information. Can I get some information? How do you do it, what's...
What is the max current nRF52840-DK source from Vdd pins, i am connecting multiple sensors through the Vdd of nRF52840-DK i want to know how much load it can source ?
Hello,
There is a problem printing the log message. I am using SDK12.3, keil compiler and segger J-Link. After modifying the project a little, normal log output is not available...
Does the nRF9160 have an ATEX component certificate? Why there is no marking such as "Ex ia IIC Ga" provided? What exactly do you understand by the term "ATEX compliance"...
After a conversation with a Nordic engineer and some research it looks like there is no official way to upgrade a product over the air from an nRF5 SDK based product to an...
I ported the Thread Secure DFU example to use FreeRTOS, however I get a hard fault if something is scheduled using the app_timer provided.
Calling coap_dfu_trigger or handling...
We have a custom PCB fitted with the nRF52840 SOC, we've previously erased and written to it via the nRF programmer tool. However, when trying to use the nrfjprog -e command...
Hi. I am having trouble connecting nrf5340 PDK to nRF Connect app on my phone.
I am using the peripheral_uart example based on https://infocenter.nordicsemi.com/index.jsp...
My customer is using a Taiyo Yuden module, EYSLSNZWW, that uses the Nordic nRF52810 chipset. We need to configure the board for Bluetooth Qualification testing. I have read...
Hello,
I use the TP4056 charging module and the 3.7V lithium battery (300mAh) and work on sdk v17.
One of the features I'm trying to create is when the charging connector...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I am trying to test ble_app_blinky_c.
I have problem with received data from peripheral which is my...
