It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hello. I evaluated the effect of temperature and humidity on BLE connection stability. I thought that the effect of humidity was higher than that of temperature, but the effect...
I'm trying to rate nrf52832 now. I'm using Keil uVision5 as my development environment.
I have written softdevice s132_nrf52_7.0.1 for the target.
I'm trying to set the...
Dear Sirs:
I use 52832, and there is 512KB internal flash.
So, I am wondering if I could have my own flash partition as below.
- Bootloader (w/ capability of firmware...
Hey all,
I've been bringing up the nRF9160 Feather and noticed some curious issues with adding an external partition when MCUboot is enabled.
I first tested the external...
We are developing a board based on nRF52840. One of the pins we would like to use as GPIO is P1.09. It is configured as GPIO (the same configuration as P0.12), but the output...
Hi,
I compiled and flashed my nrf52840-DK with "examples/peripheral/usbd_audio" and I noticed a few things:
Under Linux (Ubuntu 18.04) the microphone isn't listed. ...
We were use secure ble DFU and it work fine, recently we added serial DFU code with BLE DFU. Tested serial DFU with nrfutil and it also works. but problem in serial DFU is...
I try to invert the Signal on a PIN of the PWM module 0. It sould give out the inverted Signal of another PIN from the same PWM module.
I tried it like the code below...
We have problem in background DFU while updating Application with RBP,
Config: MCU : nRF52840 SDK : SDK16 Softdevice : s140_nrf52_7.0.1_softdevice (SDK16)
Case1:Programs...
Hi,
I'm trying to understand how to powermeter bike works. I read the ant documents and execute example bpwr ant code, but I have a question how cadence in power meters...
Hi, is it possible to reset the nvm in the nrf9160 modem back to factory settings?
I've made some changes using CFUN=0 and would now like to reset these back to as delivered...
I have an application using 4 wire SPI connecting to a 2MB data flash. An application using UART (no BLE) works fine reading and writing to this device. However with BLE enabled...
HI
I need to perform some RSA tasks on my NRF52832, but I don't see any RSA files under nrf_crypto folder of SDK v16. I am trying to use RSA from mbedtls external folder...
Hello:
I asked a question a few months ago
https://devzone.nordicsemi.com/f/nordic-q-a/54708/about-nrf52840-save-file-error
However, the follow-up did not get an answer...
Hi all,
I want to run ble_app_uart on my custom board.
I have the nRF52832 (PCA10040) connected with my board by SWD P19, SDK 16. Where should i change to make the code...
