Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I'm using a BMD200 module (with a nRF51 chip inside) and the custom_board.h provided by Rigado along with their EVK. I'm also using a BMD200 on a board I developed...
Hi There,
Under what condition(s) would a master skip a Connection Event (i.e. not transmit to the slave)?
We are currently testing using v12.1 SDK. I have configured...
After connect I try to find a service using MasterEmulator method DiscoverPipes() . I'm using event masterEmulator.LogMessage += OnLogMessage; to print logs. First it write...
I'm trying to implement an application where one board updates another board with Nordic's DFU service. I'm using the NUS client example as a basis to develop the BLE central...
Hello,
I am working with the nRF52 Development Kit and the Enhanced Shock Burst Protocol. I am trying to send Data from one Development Board to the other with static Payload...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Hi,
I want to check if the FW is properly loaded into the chip and the chip is locked. Reading APPROTECT hangs the chip even if SD is not enabled. I assume APPROTECT is...
Hello,
I work on application (written in C, compiled with GCC) which use pc-ble-driver 1.0 and nRF51822QFAC with the ble_connectivity (S130 v2.0.0) as BLE Gateway. I need...
Hi,
Anyone around that has good experience designing nfc antennas?
I'm in need of a pattern that is about 50% the size of the flex that comes with the nrf52 kit.
Doable...
Hi @ all.
I have a strange behaviour that I can't get rid of. But first some specs:
SD130 (2.0.0)
nrf51822
SDK 11
custom board
I have an application...
Hello, I'm south korea student in dongguk univ.
I use keil uvision4, nrf51822, s110 softdevice I need check the run-time.
ANd i like to check the runtime.
So i used "app_timer_cnt_get...
I am nrf51822 QFACA1 chip with s130 softdevice using nordic_sdk_11.
ble_connectivity example was not working and i am unable to do a scan from my application board.
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi all,
I have just buy a product use nrf51822 chip, I tried to find out SWIO and CLK pin out to flash but can not. Device only has RX and TX pin for Uart function, so I...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
