Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi ,
I am trying to integrate LSM6DSL to BL5340 module(laird connectivity) through SPI but I am getting failed on initialization. I am noob to NRF so could someone please...
Hi all,
I've build my own board with nrf9161 LACA, so for now I've tried to create my own board, for the moment I'm just trying to pilot my 3 leds. I've follow dev academy...
Hi, I'm building an application that will use the nrf9160 as a middle man for a websocket connection that becomes a uart connection on the main processor. Thus I want to receive...
Hello there! I am working on a central-peripheral connection, where sometimes the central is not receiving notification(s) from the peripheral. The central then asks for a...
Completing the nRF Connect SDK Fundamentals in the DevAcademy, I stumbled across this question:
Why is true not a valid answer here? Running gpio_pin_set_dt(&led, true...
Hi,
I was following the beginners tutorial and things were fine till i reached the section to create a project from scratch. I was able to build this project as well.
...
Hello,
I'm curious if there is a dependency to use the same Bluetooth module to perform OTA. If I created my own custom board, would I need to use an identical Bluetooth...
I have followed the procedure given at following url https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/create_application.html and created a application(based...
Hello,
I am working with the Signetik M1-N1 module, which is using the nRF9160 chip, as well as the DEV-M1-N1 breakout board, for evaluation and development:
Since this...
Hi,
I am working on a project that uses nrf52833 as one of I2C master to communicate with few I2C slave devices. Meanwhile there is another MCU (stm32H7) on the same bus...
Hi,
I am looking for a sample programs for my use case, wherein :
1. I have to encrypt & store the DFU image which is present in secondary partition.
2. Decrypt the...
Hi,
I am trying to mount Fat FS using pm_static.yml instead of devicetree overlay fixed partition. I can generate a memory report, but when I try to mount file system I...
Hello All,
I have a very strange problem and i can not found any solution.
I have NRF52833DK and NRF52840DK where mi code is working perfectly. Compiled with OTA is ok...
According to the docs, when CEDRXS=3 is sent to the 9160, the modem disables eDRX and the unsolicited response code. However, this means there is no response code to listen...
