Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I am using this SDK version 17.1.0 as I am using ESB in this project. So far I have gotten ESB, SPI, and UART communications working. SPI and UART are both using easy DMA...
Running on Fanstel BM15M module (nrf54L15) SDK v3.1.1, I seeing a huge timing error when trying to implement a simple timer function. In the code below, I believe I have followed...
Hello,
Caught this Nordic Skydio presentation by chance this morning and briefly mentioned was the use of a dual core processor mcu. Was this the nrf5340 or some other Nordic...
When evaluating the hardware performance, we tested the WiFi speed of the nrf54lm20 + nrf7002EB2.However, the test result was only 2MB per second.I suspect there might be...
I would like to check if our observation with nPM1300's VBAT node is expected per the IC's design.
As a background, in our application ee use a low-leakage switch to isolate...
Hi,
we have made a pull request on github to introduce the LTI support in CTS client, since one of our new devices have a display and needed a user friendly way of supporting...
Hi every one,
If any body have been succeeded in adding DFU support in Fast pair locator tag on nRF52833-DK, if so can you guide me for it?
I am getting configuration...
Hi! I am using nrf connect sdk 2.6.1 and modem firmware 1.3.7 on a nrf9160. I have an application where i need to try to get a fix on a set interval and also sometimes transmit...
Hello,
I am working with NRF52840 dongle.
I built and downloaded the hid-keyboard example to the dongle. HID keyboard function looks good that a "1" is typed by pressing...
Hello Team,
I am using SDK version 17.0.1 and have implemented OTA. I have also implemented a buttonless DFU without bonding and created a Blinky application. However, when...
Hello,
We are also having trouble installing any SDK into the VS Code Ext Pack, for development on the nRF54L15-DK. Have tried each SDK from 3.0.0 to 3.2.1 without success...
Hello,
I have a functional project to access to an SD Card with NRF54L15DK and the version 2.9.2 SDK and 3.1.0 toolchain.
But I have difficulties to access to the SD card...
Hello.
Wiring 1:
wiring 2:
Background to the case: We tested this with 2 different ppk2s and always got the same results. Our custom board works fine if we wire...
Dear all,
i have a problem when i compile a project with Segger v. 8.22a (but i tried also with v.8.26) .
The message is:
Linking 'ne_eere.elf' Linking ' ne_eere .elf...
