Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I am looking for Bluetooth Broadcaster example program that can run on nRF7002 DK. I am also looking for Bluetooth Observer example program that can run on nRF52840...
The headline says it. I've had this installation about a month and always when I say
nrfutil is taking 100% of CPU. I have up to date ubuntu 22.04 with ubuntu 22.04 in virtualbox...
Currently I'm using nRF52840 and in my application I've defined two GPIOs as an interrupt. one among them is designed such that it changes to output pin, gives a pulse then...
I want to perform ADC high-speed acquisition on IO pins. The solution is SAADC + TIMER + PPI + double buffer. The length of the buffer area is 100. The conversion cycle of...
Hi,
I'm trying to pass audio data from PDM callback function to a USB device and I'm kind of stuck.
Background: I'm using the nRF52840-DK board and 2 MP34DT05-A microphones...
Hi,
The main problem is that I have a problem with NRF Connect desktop to erase/program nrf52840 dk. I get this error:
" Error: Failed with exit code 1. One or more...
Hi,
I'm using nRF52840 DK with ncs V 2.6.0. I plan to create an mp3 or WAV audio player. I tried using the MAX98357A with the i2s nRF52840 DK board, building a project i2s...
Dear Nordic Semiconductor Team,
We are currently working on a project that involves integrating the NRF5340 MCU. After reviewing the MCU datasheet and HW design guidelines...
Trying to use the QuickStart for the Laird Pinnacle DVK. The Quickstart only shows that JLink is detected, but not supported when connected. Even connecting directly to the...
Hi,
I want to get the tick count of the system with sys_clock_tick_get(). I am using a library for NFC reader chip ST25R3916B and provided library from STM requires a platform...
Hi,
I am using https://github.com/NordicDeveloperAcademy/nRF-Connect-SDK-Fundamentals lesson5/fund_less5_exer1 as base. I have set P0.26 as UART RX. Using the code below...
Hi,
We have 3 nrf5340 LE audio dks. Two of them are flashed as BIS gateways.
One as a BIS headset. Sample used: nrf5340_audio in ncs 2.6.0
I am able to stream audios...
Hi! I am taking reference to following issue :
I have implemented same method as discussed in above link. I am getting message on client side successfully only when code...
Hi, I am trying to set up unit tests for a new zephyr project on the nrf9160. I don't want to run them on the device and instead want to run them from the command line.
...
Hi, I'm currently using nrf5340 and central_multilink and central_uart example to build connection between one central devices to several peripheral devices. But right now...
