Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
trying to build matter sample example light_bulb but getting error :
nRF connect sdk v2.9.0 & tool chain v2.9.0 using
board nrf21540dk/nrf52840
following are the...
I'm using the ESB API and I've noticed some peculiar operation when debugging with nRF Connect. I have made the following observations:
1) Giving a semaphore in the ESB...
I'm using the Async UART API and the Enhanced ShockBurst API and my code seems unstable. The RF Connect Debugger frequently crashes.
The ShockBurst User Guide specifies...
Each time I attempt to use a Zephyr API on my NORDIC device, I face the mystery of what CONFIG setting are required to go with it. For example:
To make the Async UART API...
NCS 2.7.0 with Toolchain 2.7.0
I'm working on an out of tree application derived from the example application project.
I'm using sysbuild with MCUBOOT.
The processor...
Hello, we are using the NRF52810-QCAA in LDO configuration. On reference design, there is an NC decoupling capacitor on DEC2 pin.
Is it possible to completely remove it...
Hi,
Not sure if it's a zephyr issue or a LVGL issue, so I hope I'm at the right place.
I use an 1.54 eink display with the SSD1681 driver, and LVGL. Everything goes well...
Hi Nordic,
Board:nRF54L15 DK
Code Base:peripheral_uart
Issue: Added Zephyr NVS Flash support but encountered error -22 from nvs_mount(&fs). Additionally, data cannot...
Hi everyone,
I'm working on the nrf54l15 with the nrf sdk v9.0.0 wihch I assume integrate matter version 1.4. I'm using the google nest max as a thread border router....
I am developing on a custom nRF5340 board, but I encountered a BLE-related error. To troubleshoot, I built and flashed the basic example peripheral_uart , but the following...
Hi,
We are working with nrf53-DK evaluation board, and we are using P1.02\P1.03 pins for I2C communication.
We wanted to connect a 5V I2C slave on these lines can we connect...
Hello!
I am using an nRF Connect SDK V2.9.0 with a nrf54l15. I want to set up a project with a custom board. I want to add DFU in the future, so there must be MCUboot bootloader...
Hi everyone,
I'm currently working on a low-power application and aiming to minimize sleep current as much as possible.
Thanks to some great advice I've found on this...
Hey so I am making a capstone project with Drapers lab from University of Massachusetts Lowell and one of the requirements is to create an friendly end-user GUI instead of...
