Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am trying to update the firmware from ble_center to ble_peripheral via BLE DFU(SDK version is "nRF5_SDK_17.0.2_d674dde"),
On the ble_peripheral side I can successfully...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I'm following the tutorial on youtube of Nordic Semiconductor called "Developing Bluetooth Low Energy products using nRF Connect SDK" ( here the link https://www.youtube.com...
I need to use an IPC channel between the Application and Network CPUs to notify one side when the other side has modified data in shared SRAM (region 0x20070000). My system...
Hi,
I am using nCS on nrf52833 based BL653dvk, I am based on default 32kHz CPU frequency. I need to go higher up to 40MHz, kindly suggest what configuration options I...
Hi,
I'm a newbie here.
I have a device using NRF52840 running SDK17 with SD v7 configured as a Central/Observer device doing Active Scan.
I have a few questions:
...
Hello
I am developing a board using nRF52840. I have one doubt i can used internal regulator when i power on vddh and how to select voltage level My requirement is 3.3V...
I want to use UART in the ble_app_multilink_central example. I got the Serial example project working but at the moment of moving all the sdk_config.h flags I just receive...
Hi, I want to my central device to search for peripherals by specific, hardcoced IRKs. I have setup whitelist that cooperates with bonding and peer manager. The thing is that...
I have gone through one example "servo_motor" using PWM method to control motor direction, but that seems little different from what I want to develop.
I am having nRF5340...
Hi,
I´m trying to read my ADC values. I powered de DK with USB and trying to read sensormeasurements, but I can´t see the right values.
I´m trying to read with the 12...
Hello Nordic support:
Our product used nRF52840, nRF5_SDK_17.1.0 s140_nrf52_7.2.0_softdevice.hex. Could you help us to fill the form of bluetooth BQB certification test...
I am the user who is using nrf52832. A 1:Nble connection was successful using the multi-central example. I set the tx power of the device using sd_ble_gap_tx_power_set()....
