Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello everyone,
I am working with the nrf52 DK.
I want to know if is possible to have the 5V pin when powering the DK with the Coin cell battery?
If not, how can I power...
Hello. After switching to NCS v2.0.0, we started observing a strange I2C issue - some sensors did not communicate whatsoever, and some sensors worked just fine. Further analyzing...
I have written my own python script that will be used to program devices with some additional data placed in UICR registers like public MAC address, passkey and serial number...
Hello All,
We have a new nRF9160 design - and I've updated the 9160 binaries to version 1.3.2 - on a few PCBA's - we're seeing an error like this:
Initializing COAP connection...
I followed your step by step guide available on your site for installing the SDK and Toolchain. My system are Fedora 36 with VS Code IDE, but the system detects the errors...
Is there any way to clear the app_scheduler queue? When BLE notifications are enabled, certain tasks are put into the scheduler. When BLE notifications are disabled, I would...
Hi
I am using nrs5340 chip as an SOC in my project. I want to use some Port1 Pins in my hardware design. As far as I studied in your Dev Zone, this
is inactive by default...
Hello,
I would like to measure battery voltage that is connected to the VDDH pin of an nrf5340 custom board. I understand that this is possible using the nrfx saadc driver...
Hi,
I am working with NRF52840 where I use the FDS library from the nRF5 SDK, currently SDK v15.3.0.
My issue is that I have seen my hardware suddently halts/hangs due...
Hi Team,
We are using the nrf52840 SOC for our application.Is there any way to reset the BLE stack when it is in hanging state and not able to advertisement or scanning...
Dear Support team,
in 2 different projects I am using the nRF52840-CKAA -D and nRF52840-CKAA -F .
I would like to read out the chip version by command and am trying to...
Hi, I work with a win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk. I am using peripheral_uart exemple, I need to change the connection intervals on this example...
Hi
I try to use in a mesh topology. I decided to send a string from client to nodes and receive its response. but I don't know how apply that. please help me to choose an...
hi , we have a nRF52840 DK when connected to PC via J-link there LED5 blinks . when i try to flash the code using Kiel IDE
get this error
using nRF connect the device...
