Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi!
I am using the Serial LTE Modem application from the nRF Connect SDK v.2.0.0
In the source code for this app, every call to:
int util_resolve_host(int cid, const...
Hi,
I'm a student and this is my first project on RF. I'm prototyping my own custom board. I did read in the papers of the quarterwave 2.45 GHz antenna that the PCB should...
Hi,
I am trying to understand either the timing or feature I am missing with respect to LTE, GPS and MQTT. I have read a number of posts and questions on a similar topic...
Hi, I am testing out the UART Peripheral sample on the nRF52840 DK. Since I am communicating with another MCU, I have remapped the RX and TX pins to P0.26 and P0.27 respectively...
The MenuConfig page of SEGGER IDE (ncs1.9.1)：
How should I configure this interface if I want to configure usb DFU and trigger upgrade mode via button: 1.boot_usb_dfu\Use...
I am trying to flash blinky program to nRF52840 Dongle using nRF52840 DK thorugh SWD pins. I successfully implemented that using Segger Embedded Studio by following the steps...
I am working on a project that is being ported from the nRF52840 to the nRF5340 and the once unified radio and app codebase needs to be split to the app CPU and network CPU...
Hi,
I found a odd thing when I try to get the value of ERRORSRC of uarte0 in the problem.
Sometimes the project of my customer have an uart error, when they read the value...
Hi,
I am testing NFC read/ write examples . in nRF 5 SDK 17.1.0
I am trying to write the tag using PN532 using the adafruit tag reader example but i receive error like...
Hi
I am using nrf52832 on that I want to use spi communication.
Is it possible to use half-duplex communication on spi protocol?
In full-duplex mode after sending...
I'm currently trying to make a new board definition for our PCB, which by mistake has been fitted with an nrf9160-SIBA rather than a SICA. When trying to make a new board...
Hi,
I need assistance in nordic thingy52 ble communication. I am using node and bridge code from the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
If I...
Hi Nordic Support,
I have been waiting for many years to see our end-user devices (Android, iOS, Windows, and Linux) such as smartphones, tablets, and computers to support...
Hello,
Right now our application developed using s140_nrf52_6.0.0_softdevice, SDK 15.0.0 for NRF52840 chip.
Need help on migrating to BLE 5.
Which SDK & soft device...
