Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi Nordic,
I'm able to do dfu without validation after few days of studying documentations and forum.
Here is the settings page i'm flashing:
But i had to disable...
Hello all,
the sensor is selected and so far powered via an external power supply, while the nrf52dk is powered via the USB, however, I am not sure how to properly organize...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
Recently I just found that when clicking the flash option in the vscode, the IDE only builds...
Hi,
I'm using the saadc and I notice that the max value that saadc can convert is 3,3V. If I try to convert an higher value, the result has no sense. For my project, I need...
Currently I am working on a open thread project.
Right now I am facing an issue in which my board/code is getting reset every time after I have done some changes in my previous...
Hello,
Currently In customized PCB board, nRF52832 is connected to both HFCLK(32MHz) and LFCLK(32MHz).
It takes up too much space. So HW engineer asked me to consider...
Hello. I have a device that connects to desktop app through usbuart-to-ble converter and I'm trying to simulate it using nrf52832. I've started from ble_blinky example using...
Dear,
Based on the material ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf5340%2Fqspi.html ), Encryption should be enabled independently for XIP and EasyDMA...
I want to use mcuboot together with LittleFS/NVS and a custom partition foo with my own flash storage routines. It works as long CONFIG_BOOTLOADER_MCUBOOT= n.
But with CONFIG_BOOTLOADER_MCUBOOT...
Hello,
I just received an nRF21540 EK, I am trying to use it on my current hardware which is only for scanning beacons (won't transmit) so need use it as LNA in the received...
Hi everyone. I have to turn off the bluetooth module to save battery. I am using the SDK example "ble_app_template_pca10056_s140". To start the advertisement I use the "ble_advertising_start...
project set up: Development board used nrf52832 ,SDK 15.0 ,SEGGER 5.10
actually i want to read data string from ESP32 using nrf52832 via UART (RX,TX) and send it to nrf...
Hello All,
We are using Power Profilier Kit 2 for measuring the current consumption of our device.
We Start the measurement at 14:16 PM. after 1 hour and 39 minutes (at...
