Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I want to make a thread protocol based luminaire product, there will be 300+ luminaires and 10+ OTBRs, and then control them through the cloud platform. Now I need to verify...
Hi. I apologize in advance if this question is in the wrong place or is too elementary for this location/audience. I have prototyped a product using two Nano 33 BLE arduinos...
Hello, I developed for my customer, a ZigBee coordinator in last 2019, using nRF5 SDK for Thread and Zigbee v3.2.0. Now I'm debugging to add one new feature, but some time...
Hi
I want to use a mcu to update the firmware in the nrf52810 through uart,I look in the sample in the nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader...
I try to update/replace the code in a nRF52 board from 3rd party (Fanstel). They only able to provide the private key which I can create the zip file but not able to give...
For our application, if the device loses connection, we enter beacon mode for longer range, and advertise using extended advertising to broadcast more data. Beacon mode wit...
Hi, I send application data using Read blob PDU from nRF52832. nRF52832 firmware is connectivity of Serialization of nRF5_SDK_17.0.2 for UART interface.
After connection...
I have followed the Scheduler tutorial ( https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts/scheduler-tutorial ) and was able to use...
Has anyone characterized the nRF5430 ADC dynamic performance such as harmonic distortion, SFDR, SNR over frequency. I am interested in the 10-2kHz frequency range.
Th...
Hi,
I just want to know is there any Pre compiled hex files are available to convert my Thingy 91 as Thingy 52, I just want to use my Thingy 91 with Thingy 52 Bluetooth...
Hello,
I am developing a custom board using NRF52820 and I am trying run the Blinky example on it with no success.
I am trying to adapt the blinky example for PCA10056_S140...
hi support team,
i searched devzone, my question are similar with "devzone.nordicsemi.com/.../349118
it is clear we can't set it manually. and there is no API to achieve...
I'm trying to build the lwm2m_client using SES through the toolchain manager. I continue to get the following error: "Error starting process C:\ncs\v1.9.0\toolchain\opt\bin...
With KPN and Deutsche Telekom LTE-M SIMs we get dual-stack APN with both IPv4 and IPv6 IPs.
But the iBasis LTE-M SIM is giving out only IPv4, ignoring any previous +CGDCONT...
Hello, I am trying to figure out an issue that is happening in my project. I am using the NRF52840 chip and I configured the WDT correctly with WDT-> CRV = 10 * 32768 (the...
