Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello all:
I've developed an nRF52810 application based on the Blinky example. It includes buttonless DFU support and i'm able to update the firmware by an nRF52 dev kit...
I have a problem here with using saadc of nrf52832 .
The nrfx_saadC_init (), nrfx_saadC_channels_config (), nrfx_saadC_SIMPLE_mode_set (), and nrfx_saadC_buffer_set () functions...
Hello,
I started to work in a recen project with previous code developed and I want to use the current code to play 2 PWM pulses but each pulse with different duty cycle...
Hello,
we were working on integrating arduino nano ble 33 with the 3 sensors, bme680, max30102, max30205.
when using arduino uno it is working well with the two sensors...
Hello, I looked at your youtube video setting up a VS Code environment with nrf-connect sdk https://youtu.be/r2_W8rInr38 . Unfortunately I cannot find the VSIX to install...
Hello,
I'm creating a project where i have a nrf5340dk as provisioner (controlled by uart) and i want to have multiple lights or sensors in my network. How can i use the...
Hello there, I am trying to make it work some bluetooth examples for nRF52832_XXAA_REV2, but examples is designed for PCA10040 dev kit, anybody can you tell me how much rev2...
Hi,
What happened? There's crazy inflation going on of your tools package. Compare at https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools/download...
Hi
We are seeing board to board variations in actual baud rate from NRF5340 for Baud921600 setting, bit time is varying from ~938k to ~952k the HFCLK is derived from external...
I'm running an asset tracker application using nRF9160-DK.
If it is normal, LED4 lights up in green and data is sent to nRF Cloud, but LED4 lights up in yellow and no data...
Aim 1. To use connectivity device(nrf52840) PCA10056 to program field devices(nrf52840) PCA 10056 using BLE transport. 2. To have a provision to update the connectivity device...
I need to upgrade NCS1.2.0 to NCS1.6.0, the application firmware is downloaded successfully, but after restarting the IC, it still runs the previous application. I think there...
Hi everyone! I'm trying to create gateway from a raspberry pi and I have a question. How can I receive PDU mesh packets without connect to proxy node. I found info, that there...
