Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I am considering a NRF52833 + nrf21540 combination. I see in nrf21540 product specification mentioned that
Single-ended 50 Ω matched input and output
...
Hello,
I want to create tfm_ipc project for NRF52840 DK board.
I configured options like below.
But I got an error message, "create_nordic_project.py failed (1)...
I looked at Blinky, but I am still not sure how to access the GPIO pins. In Blinky, there is an led0 alias, but what about other pins? What are there aliases?
Specifically...
Hello,
I used SDK15.3
Android phone and iOS phone is master
nRF52811 module is slave
It's said that the phone can't set conn international（Android、iOS）
But slave...
Hi,
i am working on "nrf52dk" . i want to use nfc pin as gpio.
what i did is
NRF_UICR->NFCPINS = 0<<0;
CONFIG_NFCT_PINS_AS_GPIOS included in preprocessor definations...
Dear Nordic,
I'm doing network registration test with nRF9160 DK in CMW500 test network environment.
I've set CMW500 configuration up as described at "https://devzone...
For a Non-RTOS application, take ble_app_blinky for example, the application is coded by us while SD is provided by Nordic.
My understanding is that the SD is running as...
Hello, All
I saw this description in the Bluetooth 5 Go Faster. Go Further document：
Advertising sets have an ID which is used to indicate which set a given packet belongs...
Setup:
Module: nRF51822.
SDK version:nRF5_SDK_11.0.0_89a8197.
Example: ble_app_uart.
Softdevice: S130.
I use ble_nus_string_send on the BLE_GAP_EVT_ADV_REPORT...
I'm following the NCS tutorials. I'm targeting the 52840 on the 9160DK board. I'm using SES with NCS1.6.
I'm able to get the hello world to run and the message is out on...
Hello,
we are developing a customer product based on the nRF9160 and Nordic's NCS v1.4.2 where we need to send battery test data every 30s (~ 1kB, PUT method). The communication...
Hi:
I am working on a stereo microphone application using the NRF52840. I would like to have the 2 microphones output 16K samples per second (8K samples each for left and...
