Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi There,
I am using NRF52840 chips in my system. Right now I am designing antenna for the chips. I think the reference SCH of nrf52840 have been completed the match from...
I'm using nRF52 starter kit (nRF52832AA)
I'm trying to build the ANT+ BPWR tx example from Nordic (17.0.2 + 7.0.1)
Having some issues running it, but removing ant part...
Hi,
I am using nrf17.02 sdk and nrf mesh 5.0 sdk for nrf52832 dev kit.
1) I want to send the data to UART not on RTT while using the mesh example "provisioner" example...
Anyone able to run the nRF9160 DK on Window 7? I see the 3 serial ports and the mass storage device but even though I see the device in the Programmer app I get "Unsupported...
Hi dear,
Good Day!!
I am using nRF5SDK1702d674dde\examples\ble_peripheral\ble_app_uart- software to test the UART over the BLE to my mobile , The BLE was automatically...
Hello,
i am using "ble_app_uart" example code in nrf SDK to connect to bluetooth and to read-write the data after connection through nrf connect application.
write...
We are using a custom board with softdevice S132, sdk14, and freertos and ana nrf52832.
Our ble_app does:
init gpio put up a splash screen via a display on spi
...
I am starting a new project using SDK 17.0.2, DK52 dev board and Segger embedded Studio.
To create the new project I started from ble_app_buttonless_dfu and commented out...
I got the update notice for 3.6.1, the install gets to around 33% then just sits there. This happens both with upgrade and with clean install for me, I left it to hang for...
Hi all,
in my current platform I have:
a DK (we are working to implement HW modifications to use a nrf52 dongle for this purpose) that is performing as a Thread DFU...
Hello,
I am currently trying out the assert mechanism of Zephyr.
I have added CONFIG_ASSERT=y to my prj.conf file and included " sys/__assert.h " in my main.c .
My program...
Hi,
May I ask what's the minimum reference circuitry for running nrf52840 without RF? Thanks.
My scenario is as follows.
1) RF, eg, Antenna is not needed
2) GPIOTE...
Hi,
I'm developing a CENTRAL using 52832 to connect a earphone.
1.When I enable LESC, the pair fails with the AUTH_NOT_SUPP error. Why ?
What I think if the earphone...
Hi.
I'm trying to use direct advertising to connect only with devices that have already been paired.
When I start direct advertising, I get a app_error_fault_handler...
